Special Remote Control – Page 5 – Remote Control Everything

Remote Control Car Backup Camera

Overview:

I would like to turn on/off the wireless reversing camera on my car (12V). What device can you recommend?

Solution:

We recommend this 1 channel 12V universal remote control model (S1U-DC12-ANT1+C-2).

You can wire reversing camera power lines to normally open terminals B&C of receiver. Receiver and reversing camera can share the same power supply (12V) together.

This 1CH rf remote control switch operates in toggle, momentary and latched control mode (set the mode as you like freely). And you’d better choose toggle mode or latched mode. It is great for hard to reach lights or other DC/AC electrical devices. With external telescopic antenna, the receiver has farther working range (about 100m).

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on the reversing camera (connect B and C, disconnect A and B)

Press button 1 again: Turn off the reversing camera (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on the reversing camera (connect B and C, disconnect A and B)

Press button 2: Turn off the reversing camera (disconnect B and C, connect A and B)

Vibrating Beep Kit for Disabled Person

Overview:

I am looking for a system that would allow my father to alert severely disabled mother when the latter is not in the same room. Maximum range 100 m sought. The button must be easy to use. The receiver must fit in a pocket.

Solution:

We recommend a feasible solution to you. The vibrating beep receiver with three working mode (Z-06) and 500m radio transmitter (CP-1) are suitable for you. There are three working mode for this kit. Your father can switch all of them freely as he want. They are vibration mode, beep mode and vibration mode &beep mode. When the receiver is assigned to transmitter (CP-1), the whole kit’s transmitting distance is about 500m. The receiver and transmitter are small enough for your father to put it into pocket or hold it in hand. So you don’t have to worry about how to alert your severely disabled mother.

Here is the usage.

You should learn remote control:

1 Press and hold the learning button of the receiver for about 5 seconds, then release the button when LED light is on, the receiver is in the status of learning.

2 Press button of remote control within 10 seconds, if LED light flickers twice then off, it means learning is successful.

Those three working mode will be appropriate for different situation.

Vibration mode: Press the button of transmitter, the receiver vibrates for 5 seconds. If your mother doesn’t carry the receiver to her pocket at times, your father had better switch to beep mode or beep &vibrating mode in advance. He can press button of receiver to switch to beep mode or beep& vibrating mode. He presses button of transmitter, the receiver will beep or beep and vibrates together for 5 seconds. It depends on the working mode your father chooses.

This kit is easy to use. So you can rest assured that your father will alert your mother successfully with the help of those items.

High Power Remote Controller Switch Off/On Motor of Children’s Tractor

Overview:

I’m looking for a High power remote controller to switch on/off the power to my children’s “John Deere ground force” 12v tractor if necessary. According to the specifications on the tractors the motors are 330watt and are driven by 12v battery. 330/12=27.5 amps. So I guess I need a 30amp controller.

Solution:

We recommend the model of 1 channel 30amp 12V remote controller (S1PU-DC12&C-2). Its maximum current output is 30amp. It is suitable for appliances with AC110~240V or DC0~28V because of its normally open & closed relay contact. There are 3 working modes in it. The transmitting distance is about 100m (300ft). It is enough for you.

You can see its wiring diagram. We suggest that you should learn this wiring way. That will be much convenient to you.

Wire tractor’s motor to “A” terminal and negative terminal of receiver. Use a wire to connect “B” terminal and positive terminal of receiver. And wire positive and negative terminal to 12 power supply.

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on the tractor motor, the tractor moves.

Press button 2: Turn off the tractor motor, the tractor stops.

1 Channel RF Remote Controller Switch AC Lamp Off/On

This is the one-to-many series remote controller. The 1 channel rf receiver is normally open &closed contact, you can wire lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with AC 110~240V or DC 0~28V. The transmitter is 12-button and its transmitter is 500m/1500ft. That transmitter can remote control 12 lamps at most when it pairs up with 12 receivers. Here you will see an example to remote control one ac lamp with this kind of remote controller.

Here is the material.

Next step is the wiring.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2

Press button 1, turn on lamp.

Press other button, turn off lamp.

Video

Switching LED Strip Light Off/On with Motion Detectors and Time Delay Receiver

Overview:

I would like to control a 12V LED strip light with 2 motion detectors. When the detectors detect the movement of up and down, they will turn on the led strip light.

Solution:

We recommend two motion detectors (W-01) and 1 channel time delay receiver (S1DA-DC12).

Motion detectors can be installed to the wall easily with screws to different places. Detector working distance will be 100m (Open field). Detection distance is 10m. With characteristics of time delay, its time adjustment range can be 0 second~99 hours. It has normally open and closed contact, so all device which works under AC 110~240V or DC 0~28V and working current is less than 10A can be wired to that receiver.

You can connect the LED strip to B&C contact of the receiver. Switch on the power, when any one detector is triggered, the receiver will turn on the strip. After the delay time, the receiver will turn off the strip. You can set this delay time, such as 30 seconds or 1 minute or other time you to set.