August 2014 – Remote Control Everything

Delay time wireless long range remote control two lamps on/off

The wireless system is suitable for remote control appliances within long distance. It is model: S2DA-DC12-ANT2 & CB-4. The receiver (S2DA-DC12-ANT2) has two relays and you can connect two appliances to relays. The transmitter (CB-4) remote control appliances on/off within 2000m/6000ft theoretically because of the external extend antenna. The wireless system can be used to remote control lights, motors, fans, electrically operated doors/locks/windows/blinds/ cars or other appliances. For example, you can connect two lamps to receiver and use the transmitter long range remote control lamps on/off. Besides, the wireless system can set delay time for lamps on/off.

Here is the circuit diagram of receiver. You can connect two lamps to B terminal of relays in the receiver. Then supply power to receiver. When you press the button of transmitter, the lamps will turn on/off by wireless remote control.

The wireless remote control system is delay time control mode. You can set as the processes.

Firstly, you should set delay time: You press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. Two buttons of Timer 1 adjust delay time of lamp 1; two buttons of Timer 2 adjust delay time of lamp 2. “H” is Hour, “M” is Minute, and “S” is Second. For example, if you set “1 0 M 0 3” on Timer, it means the delay time on Timer 1 is 3 minutes; the delay time on Timer 2 is 10 minutes.

Secondly, Press button D on remote: Turn on lamp 1 (connect B and C, disconnect A and B).

After 3 minutes: Turn off lamp 1 by itself (disconnect B and C, connect A and B).

Press button B: Turn off lamp 1 immediately, no need to wait for delay time.

Press button C on remote: Turn on lamp 2 (connect B and C, disconnect A and B).

After 10 minutes: Turn off lamp 2 by itself (disconnect B and C, connect A and B).

Press button A: Turn off lamp 2 immediately, no need to wait for delay time.

Finally, if you want to know more something about the wireless remote control system, you can enter into the website and search the product as following:

Model: 0020485 (S2DA-DC12-ANT2 & CB-4)

Website:

http://www.carymart.com/2ch-2000m-long-distance-dc-rf-remote-controller-delay-time-adjustable-p-1493.html

http://www.ourautomation.com/2ch-2000m-long-distance-dc-rf-remote-controller-delay-time-adjustable-p-1493.html

1000m DC 5~28V Triggered RF Transmitter with External Input Wires

Question from customer:

I would like to use a 12v DC electric current to tell a remote to send a signal to the receiver. Do you have any remote transmitters that accept a current instead of requiring a button to be pressed?

Answer:

We recommend the DC 5~28V triggered transmitter (CB-2V). With external input wires, your dc12V electric current can be input transmitter CB-2V. Transmitter can be triggered at once and transmits an rf signal “ON”. When stop inputting DC power, the transmitter is triggered and then transmits an rf signal “OFF”. So this remote control transmitter can accept a current instead of requiring a button to be pressed. Its transmission distance is about 1000m/3000ft theoretically.

You can add a rocker switch between transmitter and its power supply. (the following picture shows)

And you can make this transmitter work with a receiver. (Just like picture shown). When transmitter transmits “ON” signal, the lamp is on; When transmitter transmits “OFF” signal, the lamp is off.

315Mhz/ 433Mhz DC Motor Controllers Control Lawn Mower Motors

Question from customer:

“I received the item— 2 channel motor controller( S2PF-DC12+1CV-6-2) and installed it yesterday on my remote control lawn mower that I have made. Per the instructions for momentary control, I can get 1 motor to work at a time, either motor but only one and only in forward. I then changed, per your instructions for latch and each motor will go forward if started with remote, #1 and then #2 both will run forward only, but they cannot be controlled to go in the direction that I choose. Neither motor will reverse in any mode. I have to be able to control each motor independent of each other so I can drive the mower right and left to go the direction I want. Please advise!”

Answer:

You chose the 2 channel motor controller. Although the controller has two relays for two motor, two relays will work in the same mode. That is to say, your two motors only work in momentary mode or latched mode for one time. We recommend two sets of 1 channel dc motor controllers (S1PF-DC12+1CV-4-2), which is only 30amps output and 500m/1500ft transmission distance. It controls DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V / 24V. There are two transmission frequencies, 315Mhz /433Mhz for this controller. You can install one controller set in 315Mhz to one motor, and install another controller set in 433Mhz to another motor, so that you can control each motor independent of each other. Each motor can be controlled by its only transmitter. It won’t generate any interference each other.

Usage:

Connect power supply DC12V / 24V to terminal “INPUT”; connect motor to terminal “OUTPUT”.

Setting control mode Latched: Do not connect Jumper-1 (CN1) or Jumper-2 (CN2)

Press button ▲: motor rotates in positive direction

Press button ■: motor stops

Press button ▼: motor rotates in reversal direction

Press button ■: motor stops

Setting control mode Momentary: Only connect Jumper-1 (CN1)

Press and hold button ▲: motor rotates in positive direction

Release button: motor stops

Press and hold button ▼: motor rotates in reversal direction

Release button: motor stops

Each receiver has two controlling modes, so you can set receiver 1 for latched mode and receiver 2 for momentary or set receiver 1 for momentary mode and receiver 2 for latched mode.

Wireless Remote Control Kit with Adjustable Resistor for DC Lamp

We recommend this kind of remote controller-dc rf remote controller kit with timer (S1D-DC12 & C-1), which operates in the 315/433 MHz frequency and is actuated by DC 6V, 9V, 12V and 24V. There is an adjustable resistor being installed in it. Working time of this remote controller can be adjustable between 2-40 seconds by using a screwdriver to twist the top of resistor. It can be applied to controlling lights, motors, fans, electrically operated doors/ locks/ windows/blinds/ cars or other appliances with voltage AC 110~240V or DC 0-28V.

We’d like to show you the procedure of controlling dc led lamp.

Wire led lamp to A&B terminals of receiver. And supply power to receiver and led lamp.

Press button to turn on lamp, after 2~40 seconds delay time (It depends on the position of R1): Turn off lamp by itself.

Turn R1 clockwise with screwdriver, prolong the delay time. Press button to turn on lamp and prolong delay time more than 4 seconds…

Turn R1 anti-clockwise with screwdriver, and shorten the delay time.

Press button to turn on lamp and shorten the delay time.

Video:

Wireless AC 110/220V equipment remote control relay on/off with time delay function

We recommend the wireless remote control equipment here. It is model: S1RD-AC110/220V & C-2. The receiver (S1RD-AC110/220V) can connect one AC device and use the wireless transmitter (C-2) to remote control device on/off. The transmitter can work within 100m/300ft theoretically. The wireless remote control equipment can control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with AC 110~240V or DC 0~28V. For example, you can connect one lamp to receiver and use the wireless remote control lamp on/off.

Here is the circuit diagram of receiver. You can connect one AC lamp to B terminal of receiver. Then supply power to receiver by connecting live wire to L terminal and zero wire to Z terminal. When you press the button of transmitter, the lamp will turn on/off by wireless remote control.

The wireless remote control equipment is delay time control mode. You can operate as the process:

Press button 1: Turn on lamp (connect B and C, disconnect A and B)

After delay time, turn off lamp by itself (disconnect B and C, connect A and B)

During the delay time, press button 2: Turn off lamp straightway (disconnect B and C, connect A and B)

Finally if you would like to know more something about the wireless remote control equipment, you can enter into the website and search the product as following:

Model: 0020465 (S1RD-AC110/220V & C-2)

Website:

http://www.carymart.com/1-channel-ac-110v-220v-on-off-rf-remote-controller-relay-time-delay-p-1476.html

http://www.ourautomation.com/1-channel-ac-110v-220v-on-off-rf-remote-controller-relay-time-delay-p-1476.html