30A – Remote Control Everything

12V Motors Run Forward and Reverse through High amp Load Motor Controlling Kit

Overview:

“I want a remote control receiver to control two motors walking a distance of 100 meters without obstacles. The remote control has a receiver to turn two 12V motors. For each motor I want to control forward and reverse.

The operation shall be as follows:

When I press the button, the motor runs. When I release the button, the motor stops. This also applies to the reverse. Please advise me that you?”

Solution:

We recommend high amp load motor controlling kit (S2PF-DC12&CV-6-2) to you. This controller is specially designed for controlling DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances and mechanicals with voltage DC12V/24V. With two kinds of voltage direct output, it is applied to DC 12/24V electric appliances. Transmitting distance is 500m/1500ft (theoretically).

Wiring and Operation are fairly easy.

You can connect contact terminals “A1” and “A2” to motor 1; Then you can connect contact terminals “B1” and “B2” to motor 2. Connect contact terminals “+” and “—” to power supply DC 12V or 24V;

As you described, you can choose “Momentary Mode” for your motors’ operation. Press button, motor runs; release button, motor stops.

Setting control mode Momentary: Only connect Jumper-1 (CN1)

Press and hold button ▲ on the left: Motor 1 rotates in positive direction

Release button ▲ on the left: Motor 1 stops

Press and hold button▼ on the left: Motor 1 rotates in reversal direction

Release button ▼ on the left: Motor 1 stops

Press and hold button ▲ on the right: Motor 2 rotates in positive direction

Release button▲ on the right: Motor 2 stops

Press and hold button▼ on the right: Motor 2 rotates in reversal direction

Release button ▼ on the right: Motor 2 stops

30A High Power Remote Switch for Fireplace Chimney Fan

Question from Customer:

I’m looking for solution to remotely control fireplace chimney fan on roof of hi-rise building. Desired range would by over 150- 300ft. Fan is 110v, around 2A. Power source would be on roof and antenna would be on roof.

Please let me know if you have hardware solution.

Answer:

1 channel 30A long range remote switch (S1PX-AC220-ANT2&CB-2) is very suitable for you. With 30A current and AC100~240V voltage direct output, you don’t have to provide additional power supply to controlled fireplace chimney fan because it can get power from powered receiver. The receiver is installed a external extend magnetic antenna, it will help receiver to amplify RF signal reception so that its working distance can reach 2000m(6000ft) outdoor. It is applied to hi-rise building and long range between two buildings. The transmitter enhances its transmitting function to match this kind of receiver.

The wiring procedure is simple. Look at the following picture. Wire fan’s motor to L&N terminals of receiver. Supply 110v to receiver.

There are toggle, momentary, latched modes in it. Among three modes, we suggest you to use latched mode (Do not connect Jumper-1 and Jumper-2.)

Press big button: Turn on the fireplace chimney fan.

Press small button: Turn off the fireplace chimney fan.

Winch Motor Remote Controlling

One of our customers wanted to have a remote control kit to replace his manual switch bar to control his winch motor running up and down. This is his original wiring diagram. AC 110V will input via white wire and black wire. Through converter, AC 110V will be converted to direct current. In the violet circle, this is the manual switch control area. He has to use control switch bar to control winch motor up and down. He thought that it is inconvenient to him. So he wondered if there is a favorable remote controller for him to solve this problem.

We recommend him a 2 Channel 30A remote control kit(S2U-AC220+C-3) which features in 30A high power current. It controls lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances with voltage AC110~240V or DC0~28V which is normally open and closed contact.

Our thought is that the red circle part in the following picture will be replaced by our RF receiver.

So we drew a wiring diagram. The Black and Red wires (picture above )will be connected to terminals C and terminals B on relay 1&relay 2 respectively. White and Brown wires(picture above) will be wired to Motor.

There are 4 controlling modes for your reference. They are toggle, momentary, latched, momentary + toggle. As for motor controlling, we suggest momentary mode.

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button A of remote: Turn on relay 1, motor runs up.

Release button A: Turn off relay 1, motor stops.

Press and hold button B of remote: Turn on relay 2, motor runs down.

Release button B: Turn off relay 2, motor stops.

Club Car is Controlled by High Power Remote Controller

Question from customer:

My target is to install a remote control system to my club car. The receiver will be supplied by the 12V/26A of the caddy battery. It will be fixed on the “ON/OFF” switch of the caddy. The transmitter will cut or open the switch. Do you have any suggestions?

Answer:

We recommend the model 1 channel 30A dc remote control kit (S1PX-DC12&C-2). It is 1 channel 30A remote controller with direct current output. You don’t have to supply any power to the controlled device because it will get from powered receiver. It is applied for controlling light, motors, fans, electrically operated doors/ locks/windows/ blinds/cars or other appliances with DC12. The working distance is about 100m, but if you want to prolong control distance, you can add an external extended antenna.

The wiring is very easy. Your switch is connected to “+&-” OUT terminals on the receiver. And supply DC power to another “+&-” terminals of the receiver.

And you will get a handy transmitter with 2 buttons. We recommend you can set Latched Mode for this controlling. Press button 1, start club car; press button 2, stop club car.

Heavy Duty DC Remote for 2 LED Lamps

A new product has added in our online shop. It is 2-channel high power dc remote control kit (S2PX-DC12/24+C-2) with direct dc 12V power output (there is no need to supply power to controlled devices). Maximum current of this remote is 30amp. As for its high power, it includes 12V/24VDC power and excludes 9VDC power. It is applied to controlling lights, motors, fans, electrically operated doors, locks, windows, rolling blinds, cars or other home appliances and industrial devices.

You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.

There are 4 working modes in it. They are Toggle, Momentary, Latched, Momentary + Toggle.

Setting different control modes as you want.

•1) Setting control mode Toggle: Only connect Jumper-2.

Press button 1: Turn on the relay 1

Press button 1 again: Turn off the relay 1

Press button 2: Turn on the relay 2

Press button 2 again: Turn off the relay 2

•2) Setting control mode Momentary: Only connect Jumper-1.

Press and hold button 1: Turn on the relay 1

Release button 1: Turn off the relay 1

Press and hold button 2: Turn on the relay 2

Release button 2: Turn off the relay 2

•3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button 1: Turn on the relay 1

Turn off the relay 2

Press button 2: Turn on the relay 2

Turn off the relay 1

•4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Channel 1):

Press and hold button 1: Turn on the relay 1

Release button 1: Turn off the relay 1

Control mode Toggle (Channel 2):

Press button 2: Turn on the relay 2

Press button 2 again: Turn off the relay 2

We have made a show. How to remote control 2 LED lamps by this remote?

Let’s see the following procedure.

1×2-channel high power receiver

1×2-button transmitter

2×LED lamp

1×12V power adaptor

Line

According to the wiring diagram, we only need to wire 2 lamps to the “OUTPUT1&2” terminals of receiver and supply power to” +&-” terminals of receiver.