toggle – Remote Control Everything

15 Channel RC System

This 15 Channel 6V 9V 12V 24V rf remote controller (15S1UB-DC06/09/12/24 & CP-15) is designed to learn remote codes and used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switching modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices with the transmission distance 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V. Receiver has DC input contact and you should supply dc power to receiver.

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

How to Remote Control 15 Electric Devices with One Transmitter

We recommend this kit-1 Transmitter & 15 Receivers (15S1UB-AC220 & CP-15). It can be applied in controlling lighting, motors, fans, electrically operated doors / locks / windows / blinds / cars or other electric devices with AC 110~240V or DC 0~28V. Its transmission distance is about 500m/1500ft. It has toggle, momentary and latched working modes. You can connect or disconnect jumper to the receiver to switch those working modes. This kit includes 15 receivers and 1 transmitter, so you can connect 15 electric devices to 15 receivers and control electric devices with only one transmitter.

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

Mode switching and operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

One Receiver and 4 Transmitters Remote Control 4 Lamps

One of our customers wants a simple wireless remote operate 4 led lamps from several room at his house. He needs 4 transmitters and a receiver which can be mounted in a designated place. The remote must work from receiver about 50m away and not line of sight through doors and walls.

We suggest him choose dc 4 channel remote control system (S4C-DC12& 4C-1). Maximum working current is 5amp each relay. Working distance of remote and receiver set is about 100m (300ft) in open field. This 4CH 6V9V/12V/24V wireless remote switch operates in toggle, momentary, latched, toggle + momentary control mode (set the mode as you like freely). Easy to install and operate. Just press slightly the button on the remote, you can control universal DC/AC electrical devices. The RF signal can pass through walls, doors and other barriers. As he said, we will set 4 transmitters and this receiver with same 8-bits code in advance so that they can work together.

Operation modes:

1) Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched (Relay 1~4): Press -> On, other relays Off; Press other button -> Off.

2) Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (Relay 1~4): Press and hold -> On; Release -> Off.

3) Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle (Relay 1~4): Press -> On; Press again -> Off.

4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Relay 1, 2): Press and hold -> On; Release -> Off.

Control mode Toggle (Relay 3, 4): Press -> On; Press again -> Off.

We will show you how to remote control 4 led lamps from different places.

One Receiver and 15 Transmitters- One-to-Many Remote Control System

We’d like to recommend one-to-many series remote control system: 15 channel remote control system (S15C-DC12 & 15C-1), which includes 15 transmitters and 1 receiver. The transmitter’s transmission distance is 100/300ft theoretically. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

We’d like to show how to wire lamps and remote control lamps with this system.

The initial status is A,B normally open; B,C normally closed. We wire lamps to A&B terminals of each relay one by one. Next, we supply power to receiver. (Supply AC or DC power).

There are 15 working modes in it. We will try to show you the operation.

1) Learning Momentary control mode: When the receiver is in the status of LEARNING, press transmitter 1.

Control mode Momentary (Channel 1~15): Press and hold -> On; Release -> Off.

Press and hold transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Release transmitter 1: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press and hold transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Release transmitter 15: Turn off relay 15 (disconnect A and B, connect B and C)

2) Learning Latched control mode: When the receiver is in the status of LEARNING, press transmitter 2.

Control mode Latched (Channel 1~15): Press -> On, other relays Off; Press other button -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

3) Learning Toggle control mode: When the receiver is in the status of LEARNING, press transmitter 3.

Control mode Toggle (Channel 1~15): Press -> On; Press again -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Press transmitter 1 again: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 12 (connect A and B, disconnect B and C)

Press transmitter 15 again: Turn off relay 12 (disconnect A and B, connect B and C)

4) Learning Momentary (Channel 1~8) + Latched (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 4.

5) Learning Toggle (Channel 1~8)) + Momentary (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 5l.

6) Learning Latched (Channel 1~8) + Toggle (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 6.

7) Learning Momentary (Channel 1~13) + Latched (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 7.

8) Learning Toggle (Channel 1~13) + Momentary (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 8.

9) Learning Toggle (Channel 1~5) + Momentary (Channel 6~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 9.

10) Learning Momentary (Channel 1~5) + Latched (Channel 6~10) + Momentary (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 10.

11) Learning Toggle (Channel 1~2) + Momentary (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 11.

12) Learning Momentary (Channel 1~2) + Toggle (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 12.

13) Learning Latched (Channel 1~2) + Momentary (Channel 3~10) + Toggle (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 13.

14) Learning Toggle (Channel 1~2) + Latched (Channel 3~9) + Momentary (Channel 10~15) control mode: When the receiver is in the status of LEARNING, press transmitter 14.

15) Learning Toggle (Channel 1~13) + All On / Off (Channel 14/15): When the receiver is in the status of LEARNING, press butt transmitter on 15.

Press transmitter 14: Turn on all 15 relays

Press transmitter 15: Turn off all 15 relays

Remote Controller is Applied to LED Lamp for Decoration

When you use led lamps to decorate your bed room, your balcony, your garden, your yard or do something glowing Christmas lighting ornament outdoor, you must be very tired with complex wiring, we try to make those wiring procedure easier.

A wireless wall-mounted switch and dc output receiver can be a new remote control unit (S1X-DC12&HR-1). It is dc power output so you can use it to control DC 0～28V actuated electrical devices off/on. This wall mounted switch is like ordinary wall switch from appearance, but it is wireless and operated by RF signal that can pass through walls, floors and doors. It is be affix to any place you want by double faced adhesive tape. The switch works with DC power output receiver, you LED lamps can wired to output terminals of receiver and also get power from them.

Here is the wiring diagram.

Wire dc led lamp to OUTPUT of receiver. And add power supply to receiver. This kind of receiver is designed for DC output terminals so that lamp can get power from output terminals of receiver directly as mentioned above.

Setting different control modes (We usually set toggle for lamp controlling.)

Setting control mode Toggle: Only connect Jumper-2.

Press button: Turn on the relay, terminal OUT outputs DC power, turn on led lamp.

Press button again: Turn off the relay, terminal OUT no output, turn off led lamp.