Wireless Wall-Mounted Switch Remote Control Kit for AC Lamp

We made a remote control kit which consists of a wall-mounted switch and a remote receiver (S1X-AC220&HR-1).

wall-mounted switch and receiver

When we use ordinary switch to switch home appliances off and on, we should do some wiring for home appliances, some time it is very complicated and time- consuming. Our RF wireless wall mounted switch looks like universal switch from appearance, but it is wireless and operate by RF signal that can pass through walls, floors and doors. It is can be simply affix to any place you want by double faced adhesive tape.

wall-mounted switch

Through RF signal, you don’t have to wire between switch and appliances. Wall-mounted switch works with remote receiver to remote control ac lamp.

Here is the wiring diagram.

wiring diagram

Wire ac lamp to OUTPUT of receiver. And add power supply to receiver. This kind of receiver is designed for AC output terminals so that lamp can get power from output terminals of receiver directly.

Setting different control modes (We usually set toggle for lamp controlling.)

Setting control mode Toggle: Only connect Jumper-2.

Press button: Turn on the relay, terminal OUT outputs AC power, turn on lamp.

Press button again: Turn off the relay, terminal OUT no output, turn off lamp.

2000m Tri-mode Motor Remote Controller for Skylight

Skylights are widely used in designing for residential, public, and commercial buildings. Increased day lighting can result in less electric lighting use and saving energy, lowering costs and reducing environmental pollution. Skylight can offer you beautiful view from roof. At night, you can also watch stars from skylight when you stay in bed. Maybe it is not convenient to you to open and close skylight manually. So you may want to remote control it.

Tri-mode motor remote controller with 3-button transmitter can be used in dc motor of skylight application. Applications also include light remote control, electric gate remote control, electric window / blind remote control, etc. It is added an external extended antenna, which makes its transmitting distance reach 2000m.

1

There are three working modes in it. You will see the example controlling procedure from following information.

Material preparation:

material

Wiring is very simple.

Motor is wired to B terminals of receiver. And supply power for receiver. Motor can get power from receiver.

1_05

 

wiring

Setting control mode Toggle: Only connect Jumper-2.

Press button A, motor rotates in the positive direction; Press button A again, motor stops

Press button B, motor rotates in the reversal direction; Press button B again, motor stops

toggle-mode

Setting control mode Momentary: Only connect Jumper-1.

Press and hold button A, motor rotates in the positive direction.

Release button A, motor stops

Press and hold button B, motor rotates in the reversal direction.

Release button B, motor stops

momentary-mode

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button A, motor rotates in the positive direction.

Press button B, motor rotates in the reversal direction.

Press button C, motor stops

latched-mode

Video, please click here

30amps 100M Remote Controller for Submersible Pump

Question from customer:

I am in Australia and here we have Live-Re and Neutral-Black and Earth-Green. I wish to wire a submersible pump to your radio controller then back to the consumer mains. Please advise if wiring would be.

Mains :

Live Red          to            Controller  Power Supply L

Neutral Black  to           Controller Power Supply N

Controller terminal A               to  Pump Live Red

Controller terminal B                    to Pump Neutral Black

What is the terminal C in the controller used for? How is the earth cable from the pump and the incoming power cable earth to be connected via the controller?

Answer:

We recommend you 1 channel 30amps remote controller kit (S1PU-AC220&C-2). This 1 channel 30A rf remote control kit operates in toggle, momentary and latched control mode (set the mode as you like freely). It is great for hard to reach electrical devices, remote distance is 100m. Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

1

The outputs of this receiver are relay outputs (the terminals are normally open and normally closed), they are not AC power outputs. It just amount to a switch to turn on or off device.

If you want to turn on / off the pump by this product, the connections are as following:

Live Red        to       Controller  Power Supply L

Neutral Black    to       Controller  Power Supply N

Live Red        to       Controller terminal B

Neutral Black    to       Pump Neutral Black

Controller terminal A   to           Pump Live Red

the earth cable from the pump  to     Earth – Green

circuit

Usage:

Setting control mode Toggle: Only connect Jumper-2. Control mode Toggle: Press -> On; Press again -> Off. Press button 1: Turn on the  submersible pump. Press button 1 again: Turn off the  submersible pump.

Setting control mode Momentary: Only connect Jumper-1. Control mode Momentary: Press and hold -> On; Release -> Off. Press and hold button 1: Turn on the  submersible pump. Release button 1: Turn off the  submersible pump.

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2. Control mode Latched: Press -> On, other relays Off; Press another button -> Off. Press button 1: Turn on the submersible pump. Press button 2: Turn off the  submersible pump.

How to Remote Control 240V 25 amps Electric Equipment

Question from customer:

I am looking for an RF switch and transmitter where the switch has a coil voltage up to 12v and the switch terminal can handle 240v and 25 amps. Do you have anything like this?

Answer:

We recommend 1 channel high power remote controller (S1PU-DC12&C-2). The receiver is normally open and closed contact, so you can wire the gadget which is activated by AC 110~240V or DC0~28V.  The relay outputs 30amps current for gadget. It meets your needs. The receiver is run by 12VDC, but receiver and controller gadget will be supplied power separately so that they won’t interfere to each other. The transmitter is 2-button type remote. When it works with receiver together, their working distances reach 100m.

1_02

Here is the sample of wiring method.

Suppose that we remote control a lamp. The normally open terminals are A&B. The normally open terminals are A&C. Lamp should be connected to A&C terminals. Normally open and closed contact is similar with an ON/OFF switch. The being controlled gadget cannot get power from powered receiver. We should supply additional power to it. We can supply DC or AC power to controlled gadget according to its available power supply.

1_09

Toggle mode, momentary mode and latched mode are its working modes.

Setting control mode Toggle: Only connect Jumper-1.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on the gadget

Press button 1 again: Turn off the gadget

Setting control mode Momentary: Only connect Jumper-2.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on the gadget

Release button 1: Turn off the gadget

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on the gadget

Press button 2: Turn off the gadget

How to Use One Transmitter to Remote Control 30 Receivers

Question from Customers:

I’d like to remote control my LED decoration lights. Can I use 30 similar receivers with 1 transmitter working on 6v battery to operate low voltage LED decoration lights, in one on off operation?

Answer:

Yes, we recommend this single channel dc 6V toggle 100m rf remote control kit—the receivers S1T-DC06 and the transmitter C-1.

1

We will set 30 receivers and this transmitter with same 8-bits code so that they can work together. These receivers S1T-DC06 can work on 6V battery. The control mode is toggle mode which is fixed in advance. Toggle mode is the only working mode in this remote control kit. The maximum working current of one receiver is 10amp and remote control distance is 100m (300ft).

Here comes the wiring.

Initial state: A and B terminals are normally closed; B and C terminals are normally open. We connect light to B&C terminals. And the receiver must be wired to 6V power supply. Light can share the same power supply with receiver if you do wiring follow that wiring diagram.

circuit

You can connect 30 lights to 30 receivers one by one. Press button, turn on all lights; press button again, turn off all lights.