15 channel – Remote Control Everything

15 Channel RC System

This 15 Channel 6V 9V 12V 24V rf remote controller (15S1UB-DC06/09/12/24 & CP-15) is designed to learn remote codes and used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switching modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices with the transmission distance 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V. Receiver has DC input contact and you should supply dc power to receiver.

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

How to Remote Control 15 Electric Devices with One Transmitter

We recommend this kit-1 Transmitter & 15 Receivers (15S1UB-AC220 & CP-15). It can be applied in controlling lighting, motors, fans, electrically operated doors / locks / windows / blinds / cars or other electric devices with AC 110~240V or DC 0~28V. Its transmission distance is about 500m/1500ft. It has toggle, momentary and latched working modes. You can connect or disconnect jumper to the receiver to switch those working modes. This kit includes 15 receivers and 1 transmitter, so you can connect 15 electric devices to 15 receivers and control electric devices with only one transmitter.

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

Mode switching and operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

One Receiver and 15 Transmitters- One-to-Many Remote Control System

We’d like to recommend one-to-many series remote control system: 15 channel remote control system (S15C-DC12 & 15C-1), which includes 15 transmitters and 1 receiver. The transmitter’s transmission distance is 100/300ft theoretically. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

We’d like to show how to wire lamps and remote control lamps with this system.

The initial status is A,B normally open; B,C normally closed. We wire lamps to A&B terminals of each relay one by one. Next, we supply power to receiver. (Supply AC or DC power).

There are 15 working modes in it. We will try to show you the operation.

1) Learning Momentary control mode: When the receiver is in the status of LEARNING, press transmitter 1.

Control mode Momentary (Channel 1~15): Press and hold -> On; Release -> Off.

Press and hold transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Release transmitter 1: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press and hold transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Release transmitter 15: Turn off relay 15 (disconnect A and B, connect B and C)

2) Learning Latched control mode: When the receiver is in the status of LEARNING, press transmitter 2.

Control mode Latched (Channel 1~15): Press -> On, other relays Off; Press other button -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

3) Learning Toggle control mode: When the receiver is in the status of LEARNING, press transmitter 3.

Control mode Toggle (Channel 1~15): Press -> On; Press again -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Press transmitter 1 again: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 12 (connect A and B, disconnect B and C)

Press transmitter 15 again: Turn off relay 12 (disconnect A and B, connect B and C)

4) Learning Momentary (Channel 1~8) + Latched (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 4.

5) Learning Toggle (Channel 1~8)) + Momentary (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 5l.

6) Learning Latched (Channel 1~8) + Toggle (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 6.

7) Learning Momentary (Channel 1~13) + Latched (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 7.

8) Learning Toggle (Channel 1~13) + Momentary (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 8.

9) Learning Toggle (Channel 1~5) + Momentary (Channel 6~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 9.

10) Learning Momentary (Channel 1~5) + Latched (Channel 6~10) + Momentary (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 10.

11) Learning Toggle (Channel 1~2) + Momentary (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 11.

12) Learning Momentary (Channel 1~2) + Toggle (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 12.

13) Learning Latched (Channel 1~2) + Momentary (Channel 3~10) + Toggle (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 13.

14) Learning Toggle (Channel 1~2) + Latched (Channel 3~9) + Momentary (Channel 10~15) control mode: When the receiver is in the status of LEARNING, press transmitter 14.

15) Learning Toggle (Channel 1~13) + All On / Off (Channel 14/15): When the receiver is in the status of LEARNING, press butt transmitter on 15.

Press transmitter 14: Turn on all 15 relays

Press transmitter 15: Turn off all 15 relays

Mixed-mode Remote Control Operation(15 Channel)

We designed 15 channel DC mixed- mode remote control to satisfy customers’ more need. It is still wireless control and easy to install. It can control lights, motors, fans, electrically operated doors, locks, windows, blinds, cars or other appliances with voltage AC110~240V or DC0~28V. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors. It includes toggle, momentary, latched and mixed working modes.

The following operation is the code learning and deleting and remote control operation. At first, we should prepare material.

1×15 channel RF receiver

1×15-button transmitter

4× AC lamp(They will be connected at channels at random, just for demonstration purposes, actually you can wire 15 lamps)

Power adaptor

You can follow the wiring diagram for its wiring. Then switch on power.

Deleting code:

We should delete all stored codes firstly. Press and hold learning button for 3 seconds, then release button after buzzer sounds 5 times. All stored codes are deleted successfully.

There are 15 channels in receiver. So it has 15 working modes in it. But we only show four common operation modes here. They are toggle, momentary, latched and toggle+ momentary+latched modes.

Learning mode:

Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press corresponding button of each working mode, for example, button 3 for toggle mode, button 1 for momentary mode, button 2 for latched, and button 9 for one of mixed modes (Toggle+ Momentary+Latched modes)

Toggle mode learning and operation:

Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 3 at once, buzzer sounds 3 times, the receiver learns Toggle mode successfully.

Toggle mode operation:

Press any button to control the corresponding lamp. For example, press button 1, turn on lamp 1; press button 1 again, turn off lamp 1…

After operation of each mode, we should delete previous stored codes in advance, and then start to learning next working mode.

Momentary mode learning and operation:

Do as toggle mode learning, Press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 1 at once, buzzer sounds 3 times, the receiver learns Momentary mode successfully.

Press any button to control the corresponding lamp. For example, press and hold button 6, turn on lamp 6; release button 6, turn off lamp 6…

Latched mode learning and operation:

Deleting momentary learning code, press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 2 at once, buzzer sounds 3 times, the receiver learns latched mode successfully.

Press any button to control the corresponding lamp. For example, press button 1, turn on lamp 1, other lamps are off; press button 6, turn on lamp 6, other lamps are off…

Mixed mode learning and operation: (Toggle+ Momentary+Latched modes)

Deleting latched learning code, press and hold learning button, the receiver is in the status of learning after buzzer sounds 1 time. Press button 9 at once, buzzer sounds 3 times, the receiver learns Toggle +Momentary + Latched mode successfully. (1~5 channel is T mode; 6~10 channel is M mode; 11~15 channel is L mode)

1~5 channel (T mode): press button 1, turn on lamp 1; press button 1 again, turn off lamp 1.

6~10 channel (M mode): press and hold button 6, turn on lamp 6; release button 6, turn off lamp 6.

11~15 channel (L mode): press button 11, turn on lamp 11, other lamps are off; press button 12, turn on lamp 12, other lamps are off.

Video: