one to many – Remote Control Everything

One Receiver and 15 Transmitters- One-to-Many Remote Control System

We’d like to recommend one-to-many series remote control system: 15 channel remote control system (S15C-DC12 & 15C-1), which includes 15 transmitters and 1 receiver. The transmitter’s transmission distance is 100/300ft theoretically. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

We’d like to show how to wire lamps and remote control lamps with this system.

The initial status is A,B normally open; B,C normally closed. We wire lamps to A&B terminals of each relay one by one. Next, we supply power to receiver. (Supply AC or DC power).

There are 15 working modes in it. We will try to show you the operation.

1) Learning Momentary control mode: When the receiver is in the status of LEARNING, press transmitter 1.

Control mode Momentary (Channel 1~15): Press and hold -> On; Release -> Off.

Press and hold transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Release transmitter 1: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press and hold transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Release transmitter 15: Turn off relay 15 (disconnect A and B, connect B and C)

2) Learning Latched control mode: When the receiver is in the status of LEARNING, press transmitter 2.

Control mode Latched (Channel 1~15): Press -> On, other relays Off; Press other button -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

3) Learning Toggle control mode: When the receiver is in the status of LEARNING, press transmitter 3.

Control mode Toggle (Channel 1~15): Press -> On; Press again -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Press transmitter 1 again: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 12 (connect A and B, disconnect B and C)

Press transmitter 15 again: Turn off relay 12 (disconnect A and B, connect B and C)

4) Learning Momentary (Channel 1~8) + Latched (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 4.

5) Learning Toggle (Channel 1~8)) + Momentary (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 5l.

6) Learning Latched (Channel 1~8) + Toggle (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 6.

7) Learning Momentary (Channel 1~13) + Latched (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 7.

8) Learning Toggle (Channel 1~13) + Momentary (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 8.

9) Learning Toggle (Channel 1~5) + Momentary (Channel 6~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 9.

10) Learning Momentary (Channel 1~5) + Latched (Channel 6~10) + Momentary (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 10.

11) Learning Toggle (Channel 1~2) + Momentary (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 11.

12) Learning Momentary (Channel 1~2) + Toggle (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 12.

13) Learning Latched (Channel 1~2) + Momentary (Channel 3~10) + Toggle (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 13.

14) Learning Toggle (Channel 1~2) + Latched (Channel 3~9) + Momentary (Channel 10~15) control mode: When the receiver is in the status of LEARNING, press transmitter 14.

15) Learning Toggle (Channel 1~13) + All On / Off (Channel 14/15): When the receiver is in the status of LEARNING, press butt transmitter on 15.

Press transmitter 14: Turn on all 15 relays

Press transmitter 15: Turn off all 15 relays

Long Range RF Remote For Dragonboat Competition Starting Light System

Recently, a customer came to us to look for remote control system for a starting light system for dragonboat competition, he would like to use your one 8 channel remote and 3 CB-8 transmitters for getting timing splits from 3 different locations on a race course, the distances from the receiver and the transmitter is 1500 meters, 1000 meters and 500 meters. He wanted to know it is possible to do?

This dc power long range RF remote— 0020353 (S8CA-DC12-ANT2 & CB-8) may be favorable for him. With 8 working modes, this kind of RF remote can be set different working mode as long as you like. The maximum working current of each relay is 5amp. The working distance is up to 2000m (6000FT) in open air with external mount antenna. The most important point is that one receiver can pair with three transmitters when they are used together.

As seen in the picture, each light is connected to normally open terminal of each relay individually.

So as the customer said, this remote control is for starting light system to get timing splits from 3 different locations. Then, the first person goes to 1500 meters from the receiver with the first transmitter. The second person goes to 1000 meters from the receiver with the second transmitter and the third person goes to 500 meters from the receiver with the third transmitter.

Each person in different location can remote control the same receiver.

1 Transmitter and 8 Receivers RF Long Range Control System Switch 8 Lights On and Off

I am an electrical supervisor for Acorn Lighting Services based in UK. We are a big installer of festive lighting and have been asked by some of our clients if we can supply remote switch to turn on and off all the lights which are controlled at the same time. Now I need 1 transmitter and 8 receivers all working on the same channel. The receivers will need to 240v and be capable of controlling 980 watts lights totally. Can you supply a remote control system where there is one transmitter and 8 receiver units with antenna?

We recommend the long rang one to many rf remote control kit.

This control system operating voltage is AC110~240V. It is very favorable for this customer’s need.

They are long range remote control kit with external extended antenna.

According to this customer’s requirement, we will provide him with 1 transmitter and 8 receivers to control 8 lights simultaneously. (The following picture showed what he wanted)

So each of receivers will be paired with a light.

Wiring operation is also fairly simple.

Let’s do some demonstration in practice. First, we prepare a transmitter, two receivers and two lights. Next, we will try to show how to control two lights at the same time.

Wires from light are supposed to be connected to the output terminal of the receiver. We do it one by one. And receivers must be all powered by power supply.

Pressing the big button, 2 lights will be turned on simultaneously.

Pressing the small button, 2lights will be turned off at the same time.

Online shop: www.carymart.com

One remote controller controls many video cameras

You are going to install a security system with video cameras in somewhere in you new house, the door gate, garage, porch, living room, bedrooms. Yes, it is inconvenient for you to hold many remote controllers to turn on or off those video cameras. Or sometimes, you can not find all of controllers when the house is in a mess. At this moment you wonder whether it is possible to wire some video cameras to be controlled by one remote controller or not. We have many kinds of remote transmitters and we consider a set handy electronic remote controller can help you. CB series transmitter, CB-6 is one of those transmitters, which can connect with 6 receivers. It pairs with the receiver,S1UB-DC12. You can control video cameras with just one remote controller easily.

It is so easy to install. Look at the wiring picture.

Wires on the video camera should be connected to the receiver and power supply. From the picture, the red wire from the video camera is connected to B terminal of the receiver and the black wire is connected to negative electrode of the power supply. The positive wire of the power supply is connected to C terminal of the receiver.

The transmitter and receivers should come to the “Toggle Mode”. This means pressing each button controls each video camera on or off separately.

When press button 1, the transmitter is triggered and sends out an RF signal “ON” to the receiver. After the receiver receives the signal, the corresponding video camera is on. When press button 1 again, the transmitter is triggered and sends out an RF signal “OFF” to the receiver. After the receiver receives the signal, the corresponding video camera is off…

It is really a simple and convenient way to control all video cameras from one remote controller.

Online shop: www.carymart.com/