November 2013 – Remote Control Everything

Long Range Transmitter and Receiver Control Alarm System

Question from customer:

I want a long range transmitter and customized receiver for alarm in my security office. Do you have a recommendation for which Wireless remotes or RF transmitters may be the best for the task at hand? See the below sample of diagram: All the number need LED light when the remote is “ON” and reset button for “OFF” the buzzer.

Answer:

Our remote controllers have various functions. Here we recommend a 1000M transmitter (CB-1). Encode: Fixed code by jumpers. Its unit size is 135mm x 42mm x 25mm. Power Supply: 1 x 6F22-9V battery. Its remote control distance is 2000 meters or so with customized long range receiver.

We can use it to control alarm in security office. We can prepare 20 transmitters with different codes.

When something emergency happened, press button on the transmitter, the corresponding LED light will be lighted and the buzzer will vibrate. Press button again, the corresponding LED light will be off. When the master reset button is pressed, the buzzer will reset. The receiver can be customized. The customized receiver can be 1 channel dc 12 long range with external extended antenna. Each receiver will be connected to corresponding LED light and buzzer. So it can receive signal from the corresponding transmitter.

50M Remote Control Reminder to Train Dog

Question from customer:

I would like to know which kind of vibrators will be strong enough to alert a deaf dog? I’d like to hook it to a collar and use it to train the dog and to also alert him.

Answer:

We recommend you 50M RF remote control reminder with 4 Vibration Modes (Z-02&CS-4). This remote vibrator has two parts: vibration receiver and transmitter. It is small enough for you to carry in the pocket. Press the button on transmitter and the receiver will vibrate to alert. The receiver can be controlled by transmitter from any place within a reliable distance; wireless signal pass through walls, floors and doors. It is suitable for person or animal with hearing impairment.

With antenna, its transmitting distance is about 50M. There are vibrator, LED indicator, battery, and learning button in the receiver.

The first step is deleting and learning codes:

1 Delete all stored codes:

Press and hold the button of the receiver for about 2 seconds until LED light is off, then release the button, all stored codes have been deleted successfully. At this time, the transmitter cannot control the receiver.

2 Learning remote controls:

Press the learning button of the receiver, LED light is on, the receiver is in the status of LEARNING.

Press any button of remote control within 7 seconds, if LED light flashes twice slowly then off, it means LEARNING is successful. If LED light is off after 7 seconds, it means LEARNING is failed and the receiver quits the status of LEARNING.

The second step is operation:

The receiver can learn several remote controls of different codes.

Press button A: The receiver vibrates once.

Press button B: The receiver vibrates twice. Press button C: The receiver vibrates three times. Press button D: The receiver vibrates four times.

When you press the button on transmitter, the receiver will receive the wireless signal and vibrate. Then the dog can feel the vibration.

One Transmitter Remote Controls 12 Christmas Decorative LED Lamps

Question from customer:

When Christmas Day comes, people always use LED lights to decorate house or Christmas trees. So I’m looking for a wireless remote that I can use to create a simple on off switch to 12 led light fixtures connecting to a 12V battery at different places around my home. That souds a good idea, right? Do you have a recommendation for which Wireless remotes or RF transmitters may be the best for the task at hand?

Answer:

We recommend model 12 Channel DC12V Remote Controller – 1 Transmitter & 12 Receiver (12S1UB-DC12&1CV-12). This RF remote controller has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. That is to say, you only need a transmitter to control 12 receivers. It operates in toggle, momentary, and latched mode (set the mode as you like freely). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). And it is applied for controlling lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

Here is the wiring diagram. LED lamp is connected to normally open terminals B&C. And add a wire between terminals “B&-“ and another wire to terminals “C&+”. At last, wire a plug to terminals “+&-“.

It’s easy to set and operate. You can press each button on the transmitter to control the corresponding receiver to control LED lamp. The receiver can learn at most 60 different codes for remote controlling.

Club Car is Controlled by High Power Remote Controller

Question from customer:

My target is to install a remote control system to my club car. The receiver will be supplied by the 12V/26A of the caddy battery. It will be fixed on the “ON/OFF” switch of the caddy. The transmitter will cut or open the switch. Do you have any suggestions?

Answer:

We recommend the model 1 channel 30A dc remote control kit (S1PX-DC12&C-2). It is 1 channel 30A remote controller with direct current output. You don’t have to supply any power to the controlled device because it will get from powered receiver. It is applied for controlling light, motors, fans, electrically operated doors/ locks/windows/ blinds/cars or other appliances with DC12. The working distance is about 100m, but if you want to prolong control distance, you can add an external extended antenna.

The wiring is very easy. Your switch is connected to “+&-” OUT terminals on the receiver. And supply DC power to another “+&-” terminals of the receiver.

And you will get a handy transmitter with 2 buttons. We recommend you can set Latched Mode for this controlling. Press button 1, start club car; press button 2, stop club car.

1CH 30A Remote Control Kit for Pool Light

Question from customer:

On my swimming pool I have a switch to ON/OFF the light(2 x300 watt projectors on a single switch). Do you have any solution so I can remotely ON or OFF this pool light?

Answer:

Our suggestion is that you can use 1 channel AC power&30A output remote switch (S1PX-AC220+C-2). According to the description, it is 1 channel 30A remote controller with direct current output. It is applied for controlling light, motors, fans, electrically operated doors/ locks/windows/ blinds/cars or other appliances with AC100~240V. The working distance is about 100m, but if you want to prolong control distance, you can add an external extended antenna.

The wiring is very easy. Pool lamp is connected to L&N OUT terminals on the receiver. And supply AC power to another L&N terminals of the receiver. You don’t have to supply any current to pool lamp because it can get power from powered receiver.

And you will get a handy transmitter with 2 buttons. We recommend you can set Latched Mode for this controlling. Press button 1, turn on pool lamp; press button 2, turn off pool lamp.