Retrieving Motion Detector by 1 Channel 12V Radio Module

Question from customer:

I want a kit radio module 1 channel (12V), can transmit the state of a dry contact input (on transmitter). This is to retrieve the status of a motion detector. Distance 60m open field.

Answer:

We recommend 1 channel 12V rf receiver and transmitter with dry contact input (S1L-DC12-ANT2 & CB-2N). The very special design is its transmitter with a dry contact input aside. The triggering method of this transmitter is connection of two wires on it. There is only one channel at that relay on the receiver. The output contacts of relay are normally open and closed. Working distance of transmitter and receiver with external extend antenna are 2000M / 6000ft (theoretically).

remote controller

Wiring:

Wires on the transmitter should be connected to the contacts of motion detector (original device).

The normally open contacts B&C of receiver should be connected to the device being controlled.

Maybe you can wire a lamp to the receiver. We offer three voltage versions for receiver: 9V, 12V and 24V. You can choose the right one according to the voltage of device being controlled.

wiring diagram

wiring-of-transmitter

Operation:

When the motion detector (original device) is triggered and begin to work, the transmitter is also triggered and then transmits an rf signal “ON” to the receiver. After the receiver receives the signal, contacts B&C are closed; the lamp being controlled will be turn on.

When the motion detector (original device) is not triggered and stop working, the transmitter is also triggered and then transmits an rf signal “OFF” to the receiver. After the receiver receives the signal, contacts B&C are cut; the lamp being controlled will be turn off.

 

Note:

The output contacts of motion detector should be normally open / normally closed.

Buttons on the remote are only used for test.

The big button is for testing “ON” signal. The small button is for testing “OFF” signal.

Switching LED Strip Light Off/On with Motion Detectors and Time Delay Receiver

Overview:

I would like to control a 12V LED strip light with 2 motion detectors. When the detectors detect the movement of up and down, they will turn on the led strip light.

Solution:

We recommend two motion detectors (W-01) and 1 channel time delay receiver (S1DA-DC12).

Motion detectors can be installed to the wall easily with screws to different places. Detector working distance will be 100m (Open field). Detection distance is 10m. With characteristics of time delay, its time adjustment range can be 0 second~99 hours. It has normally open and closed contact, so all device which works under AC 110~240V or DC 0~28V and working current is less than 10A can be wired to that receiver.

remote-control-kit

You can connect the LED strip to B&C contact of the receiver. Switch on the power, when any one detector is triggered, the receiver will turn on the strip. After the delay time, the receiver will turn off the strip. You can set this delay time, such as 30 seconds or 1 minute or other time you to set.

1_09

Time Delay AC Activated Remote Control for Lighting Control

We will try to make motion detector AC lamp with infrared motion sensor  (W-01) and AC activated rf receiver with time delay function (S1DA-AC220). The working distance of motion detector is 100m (open field). The detection distance is 10m. The rf receiver is an adjustable time delay receiver. This delay time is often user-selectable which can be adjusted within 0 second~99 hours.

Operation Video:

Automated Lamp control—By Motion Detector

 

Motion detector is a vital component of security, automated light control, home control, and other useful systems. It is used to detect any moving objects, particularly people. It is usually used in hall gate, corridor or staircase. We will try to make motion detector led lamp with infrared motion detector (W-01) and rf receiver with time delay function (S1DA-DC12). The working distance of motion detector is 100m (open field). The detection distance is 10m. The rf receiver is an adjustable time delay receiver. Delay time can be adjusted as you like within 0 second~99 hours.

 

 

Let’s see the following material. We have motion detector, receiver, led lamp, dc 12V power supply.

 

 

The wiring and operation pictures are as follows:

 

Wire the rf receiver to the lamp.

 

 

Set delay time: 5 seconds and switch on the power.

 

 

Hand moves around the motion detector, the light turns on automatically.

 

 

 

When there is no motion, the light will be off by itself after 5 seconds.