wireless remote control – Page 15 – Remote Control Everything

Momentary Remote Switch for Car Siren and LED Lights

Question from customer:

If I wire a 12v device into the receiver, I won’t need to connect the device to its own power source. It gets power through this receiver. Actually,I am ready to wire a 12v car siren into one channel and a set of 12v LEDs into the other, and wire the 12v DC in to my cars battery. I can honk the siren and flash the lights from the remote?

Answer:

Our suggestion is that you can choose our 2 channel momentary 12VDC power output remote controller (S2XM-DC12 & C-2).

This is 12VDC direct power output, that is to say, you don’t have to supply your siren and led lamps to its own power because they can get through this receiver if you supply power to receiver. In addition, there are two channels for your devices you want to control. It is momentary controlling mode, which means that you press and hold button, the siren blares or led lamps flash constantly, but you release button, siren stops blaring or led lamps stop flashing. Two buttons on the transmitter are controlled siren and led lamps respectively. They won’t be interfered each other.

You can follow the wiring diagram and picture to wire your siren and led lamps. Car horn is connected to terminals of relay 1 and led lamps are connected to terminals of relay 1 in parallel. Car battery is supplied to receiver. Thus, siren and led lamps can get power through receiver.

You can honk the siren by pressing button 1 on the transmitter and flash led lamps by pressing button 2 on the transmitter. One transmitter can control two or more devices at ease.

How to Remote Control Spot light

One of our customers is a lighting designer, who is in charge of stage lighting for a show. He wants to remote control 4 stage spot lights with a remote. And each button can control each light on and off respectively.

We recommend him 4 channel remote switch kit (S4T-DC12+C-4). This is a toggle mode remote controller. It is often used to light controlling. We press the button of remote, turn on the light; press the button again, turn off the light. He can switch on and off any of lights as he wants. Normally open and close terminals connection method is capable of controlling appliances with AC110~240V or DC0~28V.

We can give him a demonstration of controlling lights.

We need the following material. They are remote control kit, LED lights, power adaptors and some lines.

This is the wiring diagram and wiring picture.

Press button 1, turn on light 1; press button 1 again, turn off light 1.

Press button 2, turn on light 2; press button 2 again, turn off light 2.

Press button 3, turn on light 3; press button 3 again, turn off light 3.

Press button 4, turn on light 4; press button 4 again, turn off light4.

Switching on and off spot lights by one transmitter is very convenient to him. He can stand anywhere to control spot lights within a reliable distance (100m). The wireless RF signal can pass through walls, floors and doors.

Video:

How to Control 4 Courtyard Lamps

Question from customer:

I am looking for remote control 220v for courtyard lamp use. I need 1 transmitter and 4 canals receivers 220V. The kit will be outdoor, out of house, in the courtyard. I also want the distance for telecommand must be +/- 150 m. Do you have any style of remotes ?

Answer：

We recommend 2000M long range 4CH AC power output remote control kit to you. 4-button transmitter is compatible with 4 channel receiver. One button is to its correspondent channel. You can connect 4 courtyard lamps to receiver. This remote is 220VAC power output so you have not to supply any power to controlled courtyard lamps. With external extended antenna, the transmitting distance exceeds 150m to reach 2000m out of house. So you can rest assured that this remote can meet the telecommand distance.

Operation is very simple.

You may have this following material.

1×4-channel long range receiver

1×4-button long range transmitter

4×AC Lamp(suppose to be courtyard lamp)

220VAC Power supply

Here is the wiring diagram. You can connect 4 AC lamps to “A&B” output terminals of receiver. Then supply power to receiver.

Setting “Toggle Mode” Only connect Jumper-2 with a little jumper.

Press button A, turn on lamp 1; Press button A again, turn off lamp 1.

Press button B, turn on lamp 2; Press button B again, turn off lamp 2.

Press button C, turn on lamp 3; Press button C again, turn off lamp 3.

Press button D, turn on lamp 4; Press button D again, turn off lamp 4.

Video:

Heavy Duty DC Remote for 2 LED Lamps

A new product has added in our online shop. It is 2-channel high power dc remote control kit (S2PX-DC12/24+C-2) with direct dc 12V power output (there is no need to supply power to controlled devices). Maximum current of this remote is 30amp. As for its high power, it includes 12V/24VDC power and excludes 9VDC power. It is applied to controlling lights, motors, fans, electrically operated doors, locks, windows, rolling blinds, cars or other home appliances and industrial devices.

You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.

There are 4 working modes in it. They are Toggle, Momentary, Latched, Momentary + Toggle.

Setting different control modes as you want.

•1) Setting control mode Toggle: Only connect Jumper-2.

Press button 1: Turn on the relay 1

Press button 1 again: Turn off the relay 1

Press button 2: Turn on the relay 2

Press button 2 again: Turn off the relay 2

•2) Setting control mode Momentary: Only connect Jumper-1.

Press and hold button 1: Turn on the relay 1

Release button 1: Turn off the relay 1

Press and hold button 2: Turn on the relay 2

Release button 2: Turn off the relay 2

•3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button 1: Turn on the relay 1

Turn off the relay 2

Press button 2: Turn on the relay 2

Turn off the relay 1

•4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Channel 1):

Press and hold button 1: Turn on the relay 1

Release button 1: Turn off the relay 1

Control mode Toggle (Channel 2):

Press button 2: Turn on the relay 2

Press button 2 again: Turn off the relay 2

We have made a show. How to remote control 2 LED lamps by this remote?

Let’s see the following procedure.

1×2-channel high power receiver

1×2-button transmitter

2×LED lamp

1×12V power adaptor

Line

According to the wiring diagram, we only need to wire 2 lamps to the “OUTPUT1&2” terminals of receiver and supply power to” +&-” terminals of receiver.

Controlling light, we usually use “Toggle” mode so we only connect Jumper-2. We will turn on power when we finished connection.

Press button 1, turn on red light.

Press button 1 again, turn off red light.

Press button 2, turn on blue light.

Press button 2 again, turn off blue light.

Video:

Long Range Communication System (Remote Control Application)

Question from customer:

I need a remote valve setup for a nitrogen purging system.The valve is 100volt 10amp that needs to be controlled by latching switch setup. I’ve seen many setups everywhere that will work but my problem is that I need some sort of indications, such as a led lamp or something at the remote to verify whether the valve is open or not. Do you have something like this available?

Feasible solution:

We found a solution to solve your problem. We also made a simulation test.

You need feedback to the remote or another receiver with a signal light to verify remotely that the valve is open. We’d like to prepare two sets of remote control and make them a remote control group. The main system is 1 channel 12VDC output receiver (S1XL-DC12)+ long range transmitter (CB-2). The secondary system is still 1 channel 12VDC output receiver (S1XL-DC12) , but we use dc triggered transmitter (CB-2V, triggered method DC power 5~28V input), which is applied for one device controlling another device. That is to say, the transmitter will send out RF signal to receiver as long as it gets a 5~28V voltage from a device.

The following picture is the material preparation.

When you add the external extended antenna, you will make the remote controller working distance to 2000M in the open air.

Here is the wiring diagram.

The wired transmitter (CB-2) will work with Receiver 1 as one group. The wireless transmitter (CB-2V) will work with Receiver 2 as another group. We have a wired remote transmitter at the first receiver that it will remotely turn on a lamp at the second receiver near the wireless transmitter.

Operation:

Press big button of wireless transmitter (CB-2), send “ON” RF signal to the first receiver, turn on lamp 1(blue lamp) and trigger wired transmitter (CB-2V), wired transmitter switch on lamp (red lamp) on the second receiver.

Press small button of wireless transmitter (CB-2), send “OFF” RF signal to the first receiver, turn on lamp 1 (blue lamp) and trigger wired transmitter (CB-2V), wired transmitter switch off lamp 2 (red lamp) on the second receiver.

We can get feedback through red lamp to verify whether the controlled device (Blue lamp) is working or not.

Video: