May 2014 – Page 2 – Remote Control Everything

1 Channel RF Remote Controller Switch AC Lamp Off/On

This is the one-to-many series remote controller. The 1 channel rf receiver is normally open &closed contact, you can wire lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with AC 110~240V or DC 0~28V. The transmitter is 12-button and its transmitter is 500m/1500ft. That transmitter can remote control 12 lamps at most when it pairs up with 12 receivers. Here you will see an example to remote control one ac lamp with this kind of remote controller.

Here is the material.

Next step is the wiring.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2

Press button 1, turn on lamp.

Press other button, turn off lamp.

Video

Momentary mode 1 channel wireless receiver & transmitter with remote control

Question from customer:

I would like 2 receivers 433 mhz 1 channel and 3 remotes with 2 buttons, one button controls receiver 1, and another button controls receiver 2, momentary control mode.

Answer:

We introduce the wireless remote control device to you according to your requirement. It is model: S1M-DC12 & C-2. The receiver (S1M-DC12) is 1 channel and transmitting frequency is 315MHz/433MHz. The transmitter (C-2) has two buttons and remote control distance is 100m/300ft theoretically. One/several wireless transmitters can remote control one/several receivers at the same time. So if you would like to use two receivers and 3 transmitters at the same time, you can buy 2 receivers (S1M-DC12) and 3 transmitters (C-2). Besides, the button 1 on the transmitter remote control receiver 1,and the button 2 remote control receiver 2.

Here is the circuit diagram of receiver. You can connect one lamp to “B & C” terminal of relay in the receiver. Then supply power to receiver. When you press the button on the transmitter, the relay to close and the lamp will turn on by wireless remote control.

There is only one control mode for the wireless remote control device: momentary. You can operation as following processes:

Press and hold button 1: Turn on lamp in the receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off lamp in the receiver 1 (disconnect B and C, connect A and B)

Press and hold button 2: Turn on lamp in the receiver 2 (connect B and C, disconnect A and B)

Release button 2: Turn off lamp in the receiver 2 (disconnect B and C, connect A and B)

Finally you can also enter into the website and search the wireless remote control device as following:

Model: S1M-DC12 & C-2

Website:

S1M-DC12

http://www.carymart.com/1-channel-dc-power-rf-momentary-remote-control-receiver-circuit-p-330.html

C-2

http://www.carymart.com/2-button-100m-wireless-remote-control-transmitter-with-cover-p-214.html

RF website:

http://www.rfcontrolsystem.com/

How to Remote Control 8 Lights with 2 Remote Transmitters

Overview:

“I am trying to set up a system with two 4-channel AC receivers and two remotes. What I’d like to do is have 4 lights hooked up to each receiver: (A,B,C,D,) on one receiver and (a,b,c,d) on the second. I would like Remote 1 to turn on/off lights A and a at the same time and lights B and b at the same time. I would like remote 2 to turn on/off lights C and c at the same time and D and d at the same time.”

Solution:

Yes, we recommend two AC power output 4 channel remote receivers (S4X-AC220) and two single-button transmitters (C-1) and set them to work according to your request.

For the receivers, they work at AC 110V/220V. Lights can be wired to relay output terminals and do not need supply additional power. For the remotes, C-1 has only one button. You can set toggle mode. (Press button, turn on device; press button again, turn off device)

Wiring is as the following picture shown.

When you press the button on the remote 1, it will turn on four lights A and a, B and b at the same time.

When you press the button on the remote 1 again, it will turn off four lights A and a, B and b at the same time.

When you press the button on the remote 2, it will turn on four lights C and c, D and d at the same time.

When you press the button on the remote 2 again, it will turn off four lights C and c, D and d at the same time.

Two 4 channel AC 220V wireless receivers & two transmitters remote control light on/off

Question from customer:

I am trying to set up a system with two 4-channel AC receivers and two remotes. What I’d like to do is have 4 lights hooked up to each receiver : (A,B,C,D,) on one receiver and (a,b,c,d) on the second. I would like Remote 1 to turn on/off lights A and a at the same time and lights B and b at the same time. I would like remote 2 to turn on/off lights C and c at the same time and D and d at the same time.

Answer:

We recommend the wireless remote control facility to you for satisfying your requirement. It is model: S4X-AC220 & C-1. The receiver (S4X-AC220) is 4 channels and working voltage is AC 100~240V. The transmitter (C-1) is 1 channel and wireless remote control distance is 100m/300ft theoretically. If you connect 4 lights to receiver, you can use wireless transmitter to remote control 4 lights. Of course if you would like to use two receivers and two transmitters at the same time, we can set work mode of the wireless remote control facility for you. Then you can use two transmitters control 8 lights at the same time.

Here is the circuit diagram of receiver. You can connect 4 lamps to “A & B” terminal of relay in each receiver. Then supply power to receiver. After you press the button of transmitter, the lamp will on/off by wireless remote control.

There is only one control mode for the wireless remote control facility: toggle. You can operation to reach your requirement of control 8 lights by using two receivers and two transmitters as following:

When you press the button on the transmitter 1, it will turn on four lights A and a, B and b at the same time.

When you press the button on the transmitter 1 again, it will turn off four lights A and a, B and b at the same time.

When you press the button on the transmitter 2, it will turn on four lights C and c, D and d at the same time.

When you press the button on the transmitter 2 again, it will turn off four lights C and c, D and d at the same time.

Finally you can also enter into the website and search the wireless remote control facility as following:

Model: S4X-AC220 & C-1

Website:

S4X-AC220

http://www.carymart.com/4ch-110v-or-220v-10a-ac-power-output-rf-remote-control-receiver-4-control-modes-p-1599.html

C-1

http://www.carymart.com/1-button-100m-wireless-remote-control-transmitter-with-cover- p-213.html

RF website:

http://www.rfcontrolsystem.com/

Switching LED Strip Light Off/On with Motion Detectors and Time Delay Receiver

Overview:

I would like to control a 12V LED strip light with 2 motion detectors. When the detectors detect the movement of up and down, they will turn on the led strip light.

Solution:

We recommend two motion detectors (W-01) and 1 channel time delay receiver (S1DA-DC12).

Motion detectors can be installed to the wall easily with screws to different places. Detector working distance will be 100m (Open field). Detection distance is 10m. With characteristics of time delay, its time adjustment range can be 0 second~99 hours. It has normally open and closed contact, so all device which works under AC 110~240V or DC 0~28V and working current is less than 10A can be wired to that receiver.

You can connect the LED strip to B&C contact of the receiver. Switch on the power, when any one detector is triggered, the receiver will turn on the strip. After the delay time, the receiver will turn off the strip. You can set this delay time, such as 30 seconds or 1 minute or other time you to set.