Time delay control – Page 2 – Remote Control Everything

Customized Time Delay 6V Remote Controller for Lamp

This 1 channel dc RF remote control switch features in controlling relay off time delay. Delay time can be customized according to actual requirement. It is widely applied to control lights, motors, fans, electrically operated doors / locks / windows / blinds or other electrical devices. It is activated in 6V power supply. You need provide us with the delay time you want when ordering. E.g. delay time: 20 seconds or 1 hour or 20 minutes… The delay time is not adjustable freely. Its working current is 10ampere and working distance is 100m (300ft).

It has normally open and closed contact. It controls various lights, fans or motors with voltage AC110~240V or DC0~28V. Here is the alternate current device wiring diagram and the wiring diagram of direct current device which not share the same power supply with receiver.

Of course, if you want to remote control direct current device which shares the same power supply with receiver, you need to do some different wiring from above wiring. Suppose that you want to remote control 6V lamp. So you don’t have to supply additional power for led lamp because led lamp will get power from powered receiver as long as you wire lamp to the receiver.

Here is the wiring procedure of 6V lamp which shares the same battery with receiver. The red wire from the lamp is connected to the C terminal of the receiver and black wire from the lamp is connected to the negative electrode of the power supply. The positive wire of the supply power is connected to B terminal and positive electrode of the receiver. The negative electrode of the power supply of power supply and receiver are connected together.

We set its delay time 20seconds.

Press button 1: Turn on the lamp. After 20seconds, turn off the lamp by itself.

During the delay time, press button 2: Turn off the lamp straightway.

Time Delay Adjustable Remote for DC Motor

Reversing motor can be applied to conveyors, awnings, winches, electrically operated doors / windows / blinds or other electrical devices. To make the motor rotate in positive and reversal direction, we try to use this kind 2 channels adjustable time delay remote control kit to control dc motor.

Firstly we prepare:

1 x 2 channel delay time adjustable receiver (S2DA-DC12)

1 x 4-button transmitter(C-4)

2 x dc 12v power supply

Some lines

Secondly, see the wiring images below; C is normally open terminal; A normally closed terminal and B common terminal. Connect terminal C to the positive and connect terminal A to the negative. Terminal B is supposed to be connected to the motor.

Thirdly, it comes to operation

At first, we set delay time 8 seconds for relay 1 and 10 seconds for relay 2. Then switch on power.

Press button 1, the motor rotates continuously in the positive direction.

If we want to interrupt the rotation, we can press button 3, the motor stops rotating immediately.

Press button 2, motor rotates continuously in the reverse direction.

If we want to interrupt the reverse rotation, press button 4, the motor stops right away.

Time Delay Mode

Press button 1, the motor positive rotation will last 8 seconds which is set in advance, then stops rotating.

Press button 2, the motor reverse rotation will last 10 seconds which is preset, then stops rotating.

2-channel Wireless Remote Switch On and Off Light and Lock

One of our customers lives in large house in the countryside and enjoys a stretch of green field. Recently, he bought an adjustable time delay control kit from us because he wants to control his door lamp and lock beside the door. When he drives in and out, he can press button to open and close the door and even he can control lamp in the evening. (as the following picture shown）

This 2-channel wireless remote switch, which we provided, operates in time delay control mode. Adjustable delay time can be 0 second~99 hours. For its 2 channels, you can adjust delay time for two relays optionally according to your actual requirement. Our customer used it to turn on the lamp and open the door in the meantime.

We would like to show the simple procedure.

After preparing material, we do some wiring. Here is the wiring picture.

The remote control kit is installed on the wall. (The following is what customer did.)

The lamp and electric lock connect to normally open terminals B&C of relay 1 and relay 2 respectively. The customer adjusted delay time 1 minute for relay 1 and 30 seconds for relay 2. Button 1&3 controls relay 1; Button 2&4 controls relay 2. He drives in and out in the daytime, he can press button 1 to open the door. The door will close by itself after 30 seconds. Of course, he can press button 3 to close it immediately as soon as he goes out of the gate. In addition, lamp need to be turn on at night, he can press button 2 to turn on the lamp. And he can press button 4 to switch off the lamp at once or let it go out by itself.

Time Delay Remote Control Activate Hot Water Circulating Pump

Question from customer:

I have a hot water circulating pump: 115V AC 0.4A. I want to be able to turn it on from 3 different locations within the house and have it turn itself off after 2 to 3 minutes. Do you have any equipment which will do this?

Answer to this question:

We think this product may be you want – ac time delay remote module 0020483 (S1DA-AC220-ANT2 & CB-2). The receiver is relay output (normally open and normally closed). Power supply for the receiver and the water pump are different. That means it will not cause electromagnetic interference during water pump operation. With the external extend antenna, the RF signal can pass through walls and doors as well as floors.

The wiring diagram is shown below.

The water pump will be connected to normally open terminals “B&C”.

After wiring, press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second. As you said, we set 3 minutes.

So we set “M 0 3”, it means the delay time is 3 minutes. Press big button: Turn on hot water circulating pump. It will stop working by itself after 3 minutes. You can also press small button to turn it off immediately.

According your requirement, one receiver can be paired with 3 transmitters. Any of transmitters can remote control the pump. You are able to turn it on from 3 different locations within your house and have it turn itself off after 2 to 3 minutes by itself.

So your home hot water circulating system will be like this.

To delay the switch of fan with RF remote controller

One of our customers said that he wanted to buy a remote controller to control switch delay. He would like it to control the fan in bedroom to turn off automatically after he slept. It is very energy-saving and money-saving. So we recommend the following remote control kit with time delay function.

The major characteristic of this model is switch delay. We have timer in the receiver. So the customer can adjust delay time from 0 second to 99 hours according to their requirement.

Here is the application circuit.

From the wiring picture, wires from the fan should be connected the B&C terminal of the receiver respectively. First of all, Press buttons of “+” and “—” on the timer and adjust delay time. If customer wants to fan be off after 2 hours, he will set “H 0 2”, it means the delay time is 2 hours. Then we press button 1, the fan begins to work. After delayed time, the fan will turn off by itself .If we press button 2, the fan is turned off immediately. There is no need to wait for delay time.

Online shop: www.carymart.com/