wireless remote control – Page 5 – Remote Control Everything

1 Channel Momentary Controller Control Hydraulic Lift Up and Down

The hydraulic lift is a device used to lift or bring down loads from one floor to another in multi-storeyed buildings or stereo garage car lifting. The hydraulic lifts are used widely in cars, containers, mold making, timber processing and chemical filling for purpose of different working height need. Maybe you just want to use small-sized hydraulic lift platform to do something and just want it to be remote controlled so that it can bring you more convenience.

Here you can use 1 channel momentary controller (S1FM-AC220+CV-2-2) to remote control your hydraulic lift up and down.

This kind of controller has inversion control mode. It is 10 amps of its maximum current and 500m working distance. The operation is also very easy.

Connect live wire to terminal “L” and neutral wire to terminal “N”. Then connect AC motor to terminals “UP”, “COMMON” and “DOWN”. You can exchange “UP” and “DOWN” wires of motor to change the rotating direction of motor.

Press and hold button ▲ on remote or receiver: Terminals UP and COMMON directly output AC110V / AC220V; motor rotates continuously in positive direction.

Release button ▲ on remote or receiver: Stop the motor.

Press and hold button ▼ on remote or receiver: Terminals DOWN and COMMON directly output AC110V / AC220V; motor rotates continuously in reversal direction.

Release button ▼ on remote or receiver: Stop the motor.

1000m Range Multi-mode Beeper& Vibrator Remote Control Kit

Beeper is an audio signaling device, which is used in alarm devices, timers or other devices typically. A customer is interested in our remote-controlled beeper& remote transmitter kit. He needs 12 beepers and 12 transmitters with 1000m working distance but He wants to be able to register one transmitter to two beepers and two transmitters to one receiver. It is possible to pair up one transmitter to two beepers or two transmitters to one receiver.

This beeper kit has vibration mode and vibration mode &beeper mode other than beeper mode. The receiver works with 1000m-range transmitter. Its working distance can reach 1000m in the open field. You can control the receiver with transmitter (remote control) from any place within a reliable distance, the wireless signal can pass through walls, floors and doors.

To realize one transmitter controlling two beepers or two transmitters controlling one receiver, first of all, you should use receiver to learn codes from transmitter.

One transmitter controlling two beepers:

Press and hold the learning button of the first receiver for about 5 seconds, then release the button when LED light is on, the receiver is in the status of Learning.

Press button of remote control within 10 seconds, if LED light flashes twice then off, it means Learning is successful.

If LED light is off after 10 seconds, it means Learning is failed and the receiver quits the status of Learning.

Follow steps above to make the second receiver learn code from the transmitter.

Operation 1:

Vibration mode: Press the button of transmitter, two receivers vibrate for 5 seconds.

Beep mode: Press the button of transmitter, two receivers beep for 5 seconds.

Vibration & Beep mode: Press the button of transmitter, two receivers vibrate and beep together for 5 seconds.

Two transmitter controlling one receiver:

Press and hold the learning button of the receiver for about 5 seconds, then release the button when LED light is on, the receiver is in the status of Learning.

Press button of the first transmitter within 10 seconds, if LED light flashes twice then off, it means Learning is successful.

If LED light is off after 10 seconds, it means Learning is failed and the receiver quits the status of Learning.

Follow steps above to make the receiver learn the second transmitter.

The receiver can learn several remote controls of different codes.

Operation 2:

Vibration mode: Press the button of transmitter 1, the receiver vibrates for 5 seconds; Press the button of transmitter 2 the receiver vibrates for 5 seconds.

Beep mode: Press the button of transmitter 1, the receiver beeps for 5 seconds; Press the button of transmitter 2, the receiver beeps for 5 seconds.

Vibration & Beep mode: Press the button of transmitter 1, the receiver vibrates and beeps together for 5 seconds; Press the button of transmitter 2, the receiver vibrates and beeps together for 5 seconds.

Changing modes: As long as press the button of receiver, you can switch those three working modes optionally. Such as press the button of receiver, switch to beep mode from vibration mode; press the button of transmitter again, switch to vibration & beep mode; press the button of transmitter again, switch to vibration mode.

One Command from Transmitter Activates Four Devices Off or On at Remote Receiver

Sometimes, you want to remote control more than one electric devices just with one transmitter，but most of remote control systems only allow one command at a time to remote control one device even though they are able to activate 2 or more relays. Or you are just looking for a remote control system with range of only 100m that will allow the activation of least three or four commands simultaneously and then trigger three or four channels on the receiver at the same time.

Actually, you thought can be realized if the 4 channel 12VDC long range receiver’s interior circuit can be changed and pair with 1-button transmitter. You just need only one button on the transmitter that you can remote control 4 devices. Its working distance is beyond your thought. It can reach 2000m (no obstacles).

You wire either AC 110~240V or DC0~28V electric devices to receiver because of its normally open and closed contact terminals. Electric devices usually wire to normally open terminals for safety purpose. Especially, if it is ac power activated remote control receiver. Receiver and controlled devices will not share the same power supply from the following wiring.

On the other hand, if you want to wire dc motivated device, such as led lights or dc motors, you can look at the following wiring diagram for your reference. Motors will share the same power supply with the receiver.

When you press the button on the transmitter CB-1, it will trigger 4 relays on the receiver at the same time. As thus, four electric gadgets will be turned on at the same time once receiver received command. When you press the button again, turn off four electric gadgets simultaneously.

12v Long Range Wireless Receiver & Transmitter of Remote Control Dry Contact on/off

Question from customer:

I am looking for a Wireless transmitter Receiver system

Features:
– Receiver Power 12 v
– 6-channel Transmitter
– Output dry contact on / off
– The scope is very important we are on a boat

Answer:

We think the model: S6C-DC12-ANT2 & 1CB-6 is more suitable for you according to your requirement. This is a wireless transmitter & receiver system. The receiver (S6C-DC12-ANT2) power is 12Vand the transmitter (1CB-6) has 6 channels. The transmitter can wireless remote control the relay (dry contact) on/off in the receiver.

When you press the button of transmitter, it will launch wireless RF signal and can be received by the receiver. Then the relay (dry contact) can on/off by wireless remote control.

Besides you can turn on/off the relay (dry contact) in the receiver with transmitter (wireless remote control) within a long range (2000m/6000ft theoretically) because of the receiver with external extend antenna ( ANT2). So if you are on a boat and far away from the shore, you can mount the receiver in the appliance on the shore and use the transmitter to turn on/off the appliance by wireless remote control on the boat. The wireless transmitter & receiver system is more suitable for long range wireless remote control.

Receiver

Transmitter

The transmitter has 6 buttons, so it has six control modes to wireless remote control the relay (dry contact) on/off. And you can set different modes as you freely like as following operation:

1) Learning Toggle control mode: When the receiver is in the status of LEARNING, press button 1 of the remote control.

Control mode Toggle (Channel 1~6): Press -> On; Press again -> Off.

Press button 1: Turn on relay 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off relay 1 (disconnect B and C, connect A and B)

…

Press button 6: Turn on relay 6 (connect B and C, disconnect A and B)

Press button 6 again: Turn off relay 6 (disconnect B and C, connect A and B)

2) Learning Momentary control mode: When the receiver is in the status of LEARNING, press button 2 of the remote control.

Control mode Momentary (Channel 1~6): Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on relay 1 (connect B and C, disconnect A and B)

Release button 1: Turn off relay 1 (disconnect B and C, connect A and B)

…

Press and hold button 6: Turn on relay 6 (connect B and C, disconnect A and B)

Release button 6: Turn off relay 6 (disconnect B and C, connect A and B)

3) Learning Latched control mode: When the receiver is in the status of LEARNING, press button 3 of the remote control.

Control mode Latched (Channel 1~8): Press -> On, other relays Off; Press other button -> Off.

Press button 1: Turn on relay 1 (connect B and C, disconnect A and B)

Turn off other relay (disconnect B and C, connect A and B)

…

Press button 6: Turn on relay 6 (connect B and C, disconnect A and B)

Turn off other relay (disconnect B and C, connect A and B)

4) Learning Momentary (Channel 1~3) + Toggle (Channel 4~6) control mode: When the receiver is in the status of LEARNING, press button 4 of the remote control.

5) Learning Momentary (Channel 1~3) + Latched (Channel 4~6) control mode: When the receiver is in the status of LEARNING, press button 5 of the remote control.

6) Learning Toggle control mode (Channel 1~4) + All On / Off (Channel 5/6): When the receiver is in the status of LEARNING, press button 6 of the remote control.

Press button 5: Turn on all 6 relays

Press button 6: Turn off all 6 relays

By the way, the status of learning can be set by someone. When someone press the button of receiver, signal LED on the receiver keeps shining. The receiver enters into status of LEARNING; press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful. When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.The receiver can learn several remote controls with different codes.

Here is the circuit diagram. You can connect one appliance to the terminal of receiver. Then supply power to the receiver. When you press the button of transmitter, you can turn on/off the appliance by wireless remote control the relay (dry contact) on/off.

If you would like to know more something about the system of wireless remote control the relay (dry contact) on/off, please you enter into our website and search the product as following:

Model: 0020456 (S6C-DC12-ANT2 & 1CB-6)

Website:

http://www.carymart.com/

http://www.carymart.com/index.php?main_page=advanced_search_result&search_in_description=1&categories_id=&keyword=S6C-DC12-ANT2

How to Wireless Remote Control Two Different Voltages Equipment

Question from customer:

Can I use the receiver to control a DC 24 volt circuit on one relay and a DC 12 volt circuit on the other relay? I need 2-button remote which can control two electrical equipment respectively. If you have this remote control , please tell me as soon as possible.

Answer:

According to your requirements, Model 0020497 (S2U-DC12 & C-2L) is suitable for you. The wireless RF remote control have two parts, the receiver and the transmitter. The relay of the receiver can work at different DC voltages. They are DC 0～28V. You can connect DC 12V & 24V equipments to this receiver in accordance with your needs. The button 1 on the transmitter control one device on/off, when you press button 1, the equipment turns on; If you press the button 2 again, it turns off. The button 2 control the other equipment by the same way.

Of course, the wireless remote can control two different voltages equipment. The relay of the receiver not only can work at DC voltage but also at AC voltage (110～240V). It can remotely control one DC voltage device and the other AC voltage one, two DC voltages equipment that there are DC 0~28V to choose, two AC voltages appliances. The remote control is widely used. It can control lights, fans, motors, electrically operated doors/locks/windows/blinds/ cars or other appliances with AC 110～240V or DC 0～28V.

It is rather convenient for you to carry the remote, because the wireless RF remote control is lightweight and no wire. You can operate it by wireless RF signal that can pass through walls, doors and floors. The reliable distance can reach 100m/300ft theoretically.

Let us know more details about the remote control. The terminals A and B are norminally closed, the terminals B and c are norminally open. Output terminals Positive electrode and Negetive electrode should be wired to additional power supply. The two electrical equipment should be connected to the terminals B & C in accordance with the application circuit.

If you want to know our more wireless remote control, please log in our website. We can assemble a variety of remote controls according to your requirements.