December 2013 – Page 2 – Remote Control Everything

6000ft AC Direct Output Remote Switch for Electric Appliance

Question from customer:

I want to turn an appliance off and on in a room in my house 120ft from the room with the transmitter. Does the appliance plug into the receiver and the receiver plug into an outlet?

Answer:

We recommend 6000ft long range ac direct output remote controller (S1X-AC220-ANT2 & CB-2). The remarkable feature of this remote controller is that 220V power direct output, that is to say, appliance plugs into receiver directly and gets 220V power from powered receiver( receiver is plugged into an outlet.) The maximum current of its relay is 10 ampere which is suitable for some appliances. The working distance is longer than any other remote, which is about 6000ft in the open field. 6000ft is long enough for your remote controlling.

At first, it is the wiring. Look at the following wiring diagram. For instance, we remote control a lamp. We just need to wire lamp to “L&N” terminals of “OUT”. That is very easy. And supply ac 220V to receiver. Then lamp can get power from powered receiver.

And this receiver works with two-button long range transmitter. There are three working modes in it. They are Toggle, Momentary, and Latched modes. If there is only a device, we recommend setting latched mode.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button 1: turn on the lamp.

Press button 2: Turn off the lamp.

2 Channel Remote Control Switch Lamp On and Off to Test Receiver Work Well

Question from customer:

I want to use the remote control to replace the button of my contactor. Since the switch will be activated rarely, is it possible to test the communication with the remote to be sure that the transmitter’s battery and receiver work correctly?

Answer:

We came up with a good idea that it can replace your manual switch to remote control contactor and to test whether the transmitter’s battery and receiver work correctly. So we recommend normally open/ closed 2 channel AC remote controller (S2U-AC220+C-2). The normally open/closed contact terminals are applied to universal power supply. In other word, normally open /closed contact terminals are as a switch for device. You need to supply DC or AC power to your controlled devices. The maximum current is 10ampere for each channel and its working distance is about 100m.

We got a plan for your problem. At first, it is the wiring. Look at the following wiring diagram. A&B terminals are the normally closed terminals. B&C terminals are normally open terminals. Being controlled devices will be connected to normally open terminals. It means that it won’t work in off-state when you disconnect the circuit. We will connect an AC lamp to relay 1 and button of contactor to relay 2. They are supplied to the same power.

And this receiver works with two-button transmitter. There are four working modes in it. They are Toggle, Momentary, Latched, Momentary + Toggle. We set Toggle mode. You want to make sure the transmitter’s battery and receiver correct working but the switch will be activated rarely. You see, the lamp is for test. When you want to test remote controller, you press button 1, if the lamp is switched on, then the transmitter and receiver work. When you press button 1 again, turn off lamp. Press button 2, turn on the contactor, press button 2 again, turn off the contactor.

500M Toggle Transmitter Remote Control 4 Lamps in House

Question from customer:

I’m looking for a wireless remote that I can use to create a simple on off switch to 4 AC lights fixtures for living room, bed room, kitchen, shower room’s illumination. Do you have a recommendation for which wireless remote or RF transmitters may be better choice for this task?

Answer:

We recommend model 4Channel AC110V~220V Remote Controller – 1 Transmitter & 4 Receivers (4S1T-AC110/220V+CV-4). The AC RF remote control switch system, which is one transmitter pairs with four receivers. With about 500 meters range (theoretically), it can widely used in lights / lamps , motors, fans, cameras, video signals, audio signals, garage doors, electric shutter doors, telescopic doors, windows, cars, etc. This remote control has a toggle control mode which is the only working mode in it. It is a low cost remote control with high quality. Extremely easy to install and use. The maximum current is 3 ampere each channel.

The light wiring is fairly simple.

Connect the neutral wire to the terminal “1”, and the live wire to the terminal “2”. Connect the lamp to the terminal “5” and the neutral wire. S o you can wire your lamps to each receiver one by one.

Operation procedure:

1) Press button 1, turn on the lamp of receiver 1. Press button 1 again, turn off the lamp of receiver 1.

2) Press button 2, turn on the lamp of receiver 2. Press button 2 again, turn off the lamp of receiver 2.

3) Press button 3, turn on the lamp of receiver 3. Press button 3 again, turn off the lamp of receiver 3.

4) Press button 4, turn on the lamp of receiver 4. Press button 4 again, turn off the lamp of receiver 4.

Holding one transmitter, you can wireless remote control your any controlled lamps of house easily because the wireless signal can pass through walls, floors and doors with reliable distance.

100M 2CH Toggle Remote Control 2 AC Lamps

When you want to remote control one more AC devices, you may think about 2 channel remote receiver. This kind of toggle 2 channel remote switch (S2T-AC110~240V + C-1) may be suitable for you. It is activated by AC110V~240V power supply. The maximum current output is 3 ampere. The Coding type of receiver is learning code. You can remote control any electric devices within 100M(No obstacles).

Look at the following wiring diagram (1). We try to introduce 2 lamps controlling of this kind. First, we connect the neutral wire to the terminal “1”, and the live wire to the terminal “2”. Second, we connect the lamp 1 to the terminal “5” and the neutral wire. Third, we continue to connect the lamp 2 to the terminal “4” and the neutral wire.

Toggle mode is the only working mode of this remote. So we can do the following operation. 1) Press button 1, turn on the lamp 1; Press button 1 again, turn off the lamp 1. 2) Press button 2, turn on the lamp 2; Press button 2 again, turn off the lamp 2.

You can remote control any AC electric appliances other than lamps. It is very convenient to you because you don’t have to supply any power to controlled appliances which will get power from powered receiver.

100M 1CH Momentary Remote Control AC Motor

The 1 channel RF Momentary Remote Control (S1M-AC110~240V & C-1) features in AC110V ~220V. There are two kinds of receiver style, one is AC 110V (AC 100~120V), widely used in US, Canada…; the other is AC220V (AC 200~240V), used in UK, France…. The Coding type of receiver is learning code. Maximum working current for each channel is 3 ampere. The working distance is 100M in the open air. Momentary mode is the only working mode of this remote.

We can use this kind of remote control to control AC motor on and off. For instance, the garden irrigation system, hot water circulation system, water pump and so on. Those motors just need to be turned on and off.

Look at the following wiring diagram. From the interior analogue circuit, we connect the neutral wire to the terminal “1”, and the live wire to the terminal “2”. And then connect the motor to the terminal “5” and the neutral wire.

Momentary mode (Press and hold button -> On; Release button -> Off)) All you need to do is just press and hold slightly the button on the remote. You press and hold button to turn on motor; release button to turn off motor.