Special Remote Control – Page 2 – Remote Control Everything

1000m DC 5~28V Triggered RF Transmitter with External Input Wires

Question from customer:

I would like to use a 12v DC electric current to tell a remote to send a signal to the receiver. Do you have any remote transmitters that accept a current instead of requiring a button to be pressed?

Answer:

We recommend the DC 5~28V triggered transmitter (CB-2V). With external input wires, your dc12V electric current can be input transmitter CB-2V. Transmitter can be triggered at once and transmits an rf signal “ON”. When stop inputting DC power, the transmitter is triggered and then transmits an rf signal “OFF”. So this remote control transmitter can accept a current instead of requiring a button to be pressed. Its transmission distance is about 1000m/3000ft theoretically.

You can add a rocker switch between transmitter and its power supply. (the following picture shows)

And you can make this transmitter work with a receiver. (Just like picture shown). When transmitter transmits “ON” signal, the lamp is on; When transmitter transmits “OFF” signal, the lamp is off.

Remote Control System with Status Restore Function

We recommend this DC power no/nc contact memory function RC system (S1MU-DC06/09/12/24 & C-2). This remote control switch operates in 4 kinds of voltages, including 6V, 9V, 12V and 24V. It can remote control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances actuated by voltage ac 110~240V or DC 0~28V. Its transmission distance is 100m. There are 4 working modes in it. So you can switch working mode by connect and disconnect jumper. With function of memory, if the power is cut off, the relay will return automatically to the previous status after the power is restored.

We’d like to show the wiring and controlling of ac, dc lamps.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp or dc lamp to normally open contact B&C and supply AC 220V power or dc power to lamp.

Operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

15 Channel RC System

This 15 Channel 6V 9V 12V 24V rf remote controller (15S1UB-DC06/09/12/24 & CP-15) is designed to learn remote codes and used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switching modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices with the transmission distance 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V. Receiver has DC input contact and you should supply dc power to receiver.

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

Operation:

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

How to Remote Control 15 Electric Devices with One Transmitter

We recommend this kit-1 Transmitter & 15 Receivers (15S1UB-AC220 & CP-15). It can be applied in controlling lighting, motors, fans, electrically operated doors / locks / windows / blinds / cars or other electric devices with AC 110~240V or DC 0~28V. Its transmission distance is about 500m/1500ft. It has toggle, momentary and latched working modes. You can connect or disconnect jumper to the receiver to switch those working modes. This kit includes 15 receivers and 1 transmitter, so you can connect 15 electric devices to 15 receivers and control electric devices with only one transmitter.

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

Mode switching and operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press button 15 again: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Release button 15: Turn off Receiver 15 (disconnect B and C, connect A and B)

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, another relay Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 15: Turn on Receiver 15 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 15 (disconnect B and C, connect A and B)

One Receiver and 4 Transmitters Remote Control 4 Lamps

One of our customers wants a simple wireless remote operate 4 led lamps from several room at his house. He needs 4 transmitters and a receiver which can be mounted in a designated place. The remote must work from receiver about 50m away and not line of sight through doors and walls.

We suggest him choose dc 4 channel remote control system (S4C-DC12& 4C-1). Maximum working current is 5amp each relay. Working distance of remote and receiver set is about 100m (300ft) in open field. This 4CH 6V9V/12V/24V wireless remote switch operates in toggle, momentary, latched, toggle + momentary control mode (set the mode as you like freely). Easy to install and operate. Just press slightly the button on the remote, you can control universal DC/AC electrical devices. The RF signal can pass through walls, doors and other barriers. As he said, we will set 4 transmitters and this receiver with same 8-bits code in advance so that they can work together.

Operation modes:

1) Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched (Relay 1~4): Press -> On, other relays Off; Press other button -> Off.

2) Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (Relay 1~4): Press and hold -> On; Release -> Off.

3) Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle (Relay 1~4): Press -> On; Press again -> Off.

4) Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.

Control mode Momentary (Relay 1, 2): Press and hold -> On; Release -> Off.

Control mode Toggle (Relay 3, 4): Press -> On; Press again -> Off.

We will show you how to remote control 4 led lamps from different places.