Special Remote Control – Page 3 – Remote Control Everything

Twelve 6V/9V/12V/24V Receivers and 1 Transmitter Kit

This rf remote controller (12S1UB-DC06/09/12/24 & CV-12 ) has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. It operates in toggle, momentary, and latched mode (switch modes as you like freely by connecting or disconnecting jumper). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

We’d like to show the wiring and controlling of ac, dc lamps or dc motors.

The contact of relay of each receiver is normally open/ closed. So you need to wire ac lamp to normally open contact B&C and supply AC 220V power to lamp. When you want to remote control dc motors or lamps, you can wire them to receivers as mentioned above. But dc motor and lamps can share the same power supply if you wire as the right picture shown.

Setting control mode Toggle: Connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press button 1 again: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Press button 12 again: Turn off Receiver 12 (disconnect B and C, connect A and B)

Setting control mode Momentary: Connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press and hold button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Release button 12: Turn off Receiver 12 (disconnect B and C, connect A and B)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)

…

Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)

Press other button: Turn off Receiver 12 (disconnect B and C, connect A and B)

How to Remote Control 4 High Power Receiver with 1 Transmitter

We’d like to recommend one-to-many series: 4 channel 30amps AC RF remote control gadget (4S1PUA-AC220+1CV-4), which includes 1 transmitter and 4 receivers. The transmitter’s transmission distance is 500m/1500ft theoretically. It is designed for high power device. Then maximum current is 30amps. This wireless gadget can remote control high power lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

One transmitter can remote control 4 receivers simultaneously. If you want to use two or more receivers in the same place, you can set them with different codes. It operates in three modes, including toggle, momentary and latched. All working modes can be switched easily by connecting or disconnecting jumper.

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

Operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Press button 1 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Press button 2 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Press button 3 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Press button 4 again: Turn off the relay (disconnect A and B, connect A and C)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Release button 1: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Release button 2: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Release button 3: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Release button 4: Turn off the relay (disconnect A and B, connect A and C)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On; other relays Off; Press another button -> Off.

Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 2, 3, 4 (disconnect A and B, connect A and C)

Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 3, 4 (disconnect A and B, connect A and C)

Press button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 2, 4 (disconnect A and B, connect A and C)

Press button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 2, 3 (disconnect A and B, connect A and C)

One Receiver and 15 Transmitters- One-to-Many Remote Control System

We’d like to recommend one-to-many series remote control system: 15 channel remote control system (S15C-DC12 & 15C-1), which includes 15 transmitters and 1 receiver. The transmitter’s transmission distance is 100/300ft theoretically. This wireless gadget can remote control lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

We’d like to show how to wire lamps and remote control lamps with this system.

The initial status is A,B normally open; B,C normally closed. We wire lamps to A&B terminals of each relay one by one. Next, we supply power to receiver. (Supply AC or DC power).

There are 15 working modes in it. We will try to show you the operation.

1) Learning Momentary control mode: When the receiver is in the status of LEARNING, press transmitter 1.

Control mode Momentary (Channel 1~15): Press and hold -> On; Release -> Off.

Press and hold transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Release transmitter 1: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press and hold transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Release transmitter 15: Turn off relay 15 (disconnect A and B, connect B and C)

2) Learning Latched control mode: When the receiver is in the status of LEARNING, press transmitter 2.

Control mode Latched (Channel 1~15): Press -> On, other relays Off; Press other button -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 15 (connect A and B, disconnect B and C)

Turn off other relays (disconnect A and B, connect B and C)

3) Learning Toggle control mode: When the receiver is in the status of LEARNING, press transmitter 3.

Control mode Toggle (Channel 1~15): Press -> On; Press again -> Off.

Press transmitter 1: Turn on relay 1 (connect A and B, disconnect B and C)

Press transmitter 1 again: Turn off relay 1 (disconnect A and B, connect B and C)

…

Press transmitter 15: Turn on relay 12 (connect A and B, disconnect B and C)

Press transmitter 15 again: Turn off relay 12 (disconnect A and B, connect B and C)

4) Learning Momentary (Channel 1~8) + Latched (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 4.

5) Learning Toggle (Channel 1~8)) + Momentary (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 5l.

6) Learning Latched (Channel 1~8) + Toggle (Channel 9~15) control mode: When the receiver is in the status of LEARNING, press transmitter 6.

7) Learning Momentary (Channel 1~13) + Latched (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 7.

8) Learning Toggle (Channel 1~13) + Momentary (Channel 14~15) control mode: When the receiver is in the status of LEARNING, press transmitter 8.

9) Learning Toggle (Channel 1~5) + Momentary (Channel 6~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 9.

10) Learning Momentary (Channel 1~5) + Latched (Channel 6~10) + Momentary (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 10.

11) Learning Toggle (Channel 1~2) + Momentary (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 11.

12) Learning Momentary (Channel 1~2) + Toggle (Channel 3~10) + Latched (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 12.

13) Learning Latched (Channel 1~2) + Momentary (Channel 3~10) + Toggle (Channel 11~15) control mode: When the receiver is in the status of LEARNING, press transmitter 13.

14) Learning Toggle (Channel 1~2) + Latched (Channel 3~9) + Momentary (Channel 10~15) control mode: When the receiver is in the status of LEARNING, press transmitter 14.

15) Learning Toggle (Channel 1~13) + All On / Off (Channel 14/15): When the receiver is in the status of LEARNING, press butt transmitter on 15.

Press transmitter 14: Turn on all 15 relays

Press transmitter 15: Turn off all 15 relays

Long Range Vibrating and Beep Alerts Kit

Vibrating alerts are primarily used when a user (deaf people or aged people) cannot hear the ring tone (a noisy environment or through hearing difficulty) or want s a more discreet notification. Vibrating alerts is used in mobile phones. If you put vibrator to a hard surface, it will be louder than a ringtone. In fact, we integrate vibration and beep function into one item. So we’d like recommend this kind of 1000m rf tri-mode wireless vibrator kit (12Z-06 & CB-12). It includes 12 vibrators and a 12-button transmitter. This vibrator kit’s transmission distance is about 1000m. There are four working modes in them. They are vibration, beep, vibration and beep.

Here is the usage of vibrator kit.

The first step is learning.

1) Press and hold the learning button of the receiver(vibrator) for about 5 seconds, then release the button when LED light is on, the receiver (vibrator)is in the status of Learning.
2) Press button of remote control within 10 seconds, if LED light flashes twice then off, it means Learning is successful.
If LED light is off after 10 seconds, it means Learning is failed and the receiver quits the status of Learning.
3) The receiver (vibrator) can learn several remote controls of different codes.

So the receiver (vibrator) will learn transmitter’s signal from its button 1 to button 12.

The next step is controlling.

Vibration mode: Press the button of transmitter, the receiver vibrates for 5 seconds.

Beep mode: Press the button of transmitter, the receiver beeps for 5 seconds.

Vibration & Beep mode: Press the button of transmitter, the receiver vibrates and beeps together for 5 seconds.

Changing modes: As long as press the button of receiver, you can switch those three working modes optionally. Such as press the button of receiver, switch to beep mode from vibration mode; press the button of transmitter again, switch to vibration & beep mode; press the button of transmitter again, switch to vibration mode.

Each button of transmitter can control one receiver.

How to Control Linear Actuator by Remote Transmitter and Manual Switch

30 amps dc output controller (S1PF-DC12-ANT2+CB-4) is designed for motor controlling. It is compatible with many kinds of motor which is actuated by DC 12V/24V. It is applied to DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances. We add external extended antenna to the receiver, so we make its transmitting distance reach to 2000m (6000ft) in the open field. The receiver pairs up with a 4-button transmitter and has manual switches on itself. Both transmitter and manual switches can send signal to receiver.