Remote Control Lights – Page 3 – Remote Control Everything

One Transmitter Remote Controls 12 Christmas Decorative LED Lamps

Question from customer:

When Christmas Day comes, people always use LED lights to decorate house or Christmas trees. So I’m looking for a wireless remote that I can use to create a simple on off switch to 12 led light fixtures connecting to a 12V battery at different places around my home. That souds a good idea, right? Do you have a recommendation for which Wireless remotes or RF transmitters may be the best for the task at hand?

Answer:

We recommend model 12 Channel DC12V Remote Controller – 1 Transmitter & 12 Receiver (12S1UB-DC12&1CV-12). This RF remote controller has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. That is to say, you only need a transmitter to control 12 receivers. It operates in toggle, momentary, and latched mode (set the mode as you like freely). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). And it is applied for controlling lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

Here is the wiring diagram. LED lamp is connected to normally open terminals B&C. And add a wire between terminals “B&-“ and another wire to terminals “C&+”. At last, wire a plug to terminals “+&-“.

It’s easy to set and operate. You can press each button on the transmitter to control the corresponding receiver to control LED lamp. The receiver can learn at most 60 different codes for remote controlling.

1CH 30A Remote Control Kit for Pool Light

Question from customer:

On my swimming pool I have a switch to ON/OFF the light(2 x300 watt projectors on a single switch). Do you have any solution so I can remotely ON or OFF this pool light?

Answer:

Our suggestion is that you can use 1 channel AC power&30A output remote switch (S1PX-AC220+C-2). According to the description, it is 1 channel 30A remote controller with direct current output. It is applied for controlling light, motors, fans, electrically operated doors/ locks/windows/ blinds/cars or other appliances with AC100~240V. The working distance is about 100m, but if you want to prolong control distance, you can add an external extended antenna.

The wiring is very easy. Pool lamp is connected to L&N OUT terminals on the receiver. And supply AC power to another L&N terminals of the receiver. You don’t have to supply any current to pool lamp because it can get power from powered receiver.

And you will get a handy transmitter with 2 buttons. We recommend you can set Latched Mode for this controlling. Press button 1, turn on pool lamp; press button 2, turn off pool lamp.

Scaring Birds Remote Controlling Flashing Lamp

Question from customer:

I want to use the 1 channel remote control to operate flashing lamp in a tree to scare birds in the evening from roosting.

Answer:

It is a good idea to scare birds from roosting in the evening by remote controlling a flashing lamp because you must be very furious at noise to spoil your sweet dream or interfere with your other activities. Our suggestion is that you can choose this 1 channel dc triggered long distance remote gadget (S1X-DC12-ANT2+CB-2). You can wiring one flashing lamp to relay channel. Flashing lamp can get power from receiver directly. With external extended antenna, this remote gadget will transmit signal up to 2000m (6000ft) in the open field.

Here is the wiring diagram. Flashing lamp is connected to terminals A&B of receiver. And supply power to receiver.

Operation:

There are two working modes for your information. They are momentary and latched modes.

1. Setting control mode Momentary: Only connect Jumper-1.

Press and hold big button: Turn on the relay, terminal A&B output DC power. The flashing lamp will keep flashing constantly.

Release big button: Turn off the relay, terminal A&B no output. There is no flashing from lamp.

2. Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press big button: Turn on the relay, terminal A&B output DC power. The flashing lamp will be remote controlled and keep flashing all the time.

Press small button: Turn off the relay, terminal A&B no output. The lamp is off.

Toggle Remote Controller for 2 LED Lights

Question from customer：

Hello, can you supply me with 2 single on/off receivers with using just 1 transmitter? I have 2 separate 24 volt led lamps in separate locations in my motor home, but I just want to operate all lights from 1 transmitter.

Answer：

We recommend you 2 voltage output toggle receivers (S1XT-DC24) and 1 transmitter (C-2). Wire each led lamp to each channel of receiver. It is voltage direct output. The led lamps can get power through receiver directly. It outputs DC24V power. With fixed toggle working mode, you can use transmitter to press button 1 & 2 to turn on lamps, and then press again to turn off lamps. There is no interference between receivers.

We prepare a simple demonstration for your reference. At first, we prepare the following material.

They are remote control kits, led lamps, power adaptors, lines

According to the following wiring diagram, we made wiring. Two led lamps are connected to A&B terminals of receivers respectively. And supply 24V power to receiver.

Press button 1, switch on lamp 1.

Press button 1 again, switch off lamp 1.

Press button 2, switch on lamp 2.

Press button 2 again, switch off lamp 2.

Video:

How to Remote Control Spot light

One of our customers is a lighting designer, who is in charge of stage lighting for a show. He wants to remote control 4 stage spot lights with a remote. And each button can control each light on and off respectively.

We recommend him 4 channel remote switch kit (S4T-DC12+C-4). This is a toggle mode remote controller. It is often used to light controlling. We press the button of remote, turn on the light; press the button again, turn off the light. He can switch on and off any of lights as he wants. Normally open and close terminals connection method is capable of controlling appliances with AC110~240V or DC0~28V.

We can give him a demonstration of controlling lights.

We need the following material. They are remote control kit, LED lights, power adaptors and some lines.

This is the wiring diagram and wiring picture.

Press button 1, turn on light 1; press button 1 again, turn off light 1.

Press button 2, turn on light 2; press button 2 again, turn off light 2.

Press button 3, turn on light 3; press button 3 again, turn off light 3.

Press button 4, turn on light 4; press button 4 again, turn off light4.

Switching on and off spot lights by one transmitter is very convenient to him. He can stand anywhere to control spot lights within a reliable distance (100m). The wireless RF signal can pass through walls, floors and doors.

Video: