wireless remote control – Page 3 – Remote Control Everything

How to Remote Control 8 Lights with 2 Remote Transmitters

Overview:

“I am trying to set up a system with two 4-channel AC receivers and two remotes. What I’d like to do is have 4 lights hooked up to each receiver: (A,B,C,D,) on one receiver and (a,b,c,d) on the second. I would like Remote 1 to turn on/off lights A and a at the same time and lights B and b at the same time. I would like remote 2 to turn on/off lights C and c at the same time and D and d at the same time.”

Solution:

Yes, we recommend two AC power output 4 channel remote receivers (S4X-AC220) and two single-button transmitters (C-1) and set them to work according to your request.

For the receivers, they work at AC 110V/220V. Lights can be wired to relay output terminals and do not need supply additional power. For the remotes, C-1 has only one button. You can set toggle mode. (Press button, turn on device; press button again, turn off device)

Wiring is as the following picture shown.

When you press the button on the remote 1, it will turn on four lights A and a, B and b at the same time.

When you press the button on the remote 1 again, it will turn off four lights A and a, B and b at the same time.

When you press the button on the remote 2, it will turn on four lights C and c, D and d at the same time.

When you press the button on the remote 2 again, it will turn off four lights C and c, D and d at the same time.

Switching LED Strip Light Off/On with Motion Detectors and Time Delay Receiver

Overview:

I would like to control a 12V LED strip light with 2 motion detectors. When the detectors detect the movement of up and down, they will turn on the led strip light.

Solution:

We recommend two motion detectors (W-01) and 1 channel time delay receiver (S1DA-DC12).

Motion detectors can be installed to the wall easily with screws to different places. Detector working distance will be 100m (Open field). Detection distance is 10m. With characteristics of time delay, its time adjustment range can be 0 second~99 hours. It has normally open and closed contact, so all device which works under AC 110~240V or DC 0~28V and working current is less than 10A can be wired to that receiver.

You can connect the LED strip to B&C contact of the receiver. Switch on the power, when any one detector is triggered, the receiver will turn on the strip. After the delay time, the receiver will turn off the strip. You can set this delay time, such as 30 seconds or 1 minute or other time you to set.

4 Channel DC Output Remote Controller for Garden Lamps and Pond Pump

Overview:

I’m interested in buying transmitters and receivers 12 volts for three garden lights and one pond pump, but could you please advise me on which accessories and channels I would need for this?

Solution:

We recommend 4 Channel DC Output Long Range Kit (S4X-DC12-ANT2 & CB-4L). 4 channels can output 12V power, so garden lights and pond pump can be wired to terminals of relays respectively. It is 10amps of each channel. The transmitting distance is up to 2000m (6000FT) in open air with external mount antenna. It is very appropriate for outside pond pump and garden lights.

Wire three garden lights and pond pump to four relay terminals one by one. Supply 12V power, switch on power. Receiver, garden lights and pond pump turn on immediately.

Setting control mode Toggle: (Only connect Jumper-2).

Press button A, turn on light 1; Press button A again, turn off light 1.

Press button B, turn on light 2; Press button B again, turn off light 2.

Press button C, turn on light 3; Press button B again, turn off light 3.

Press button D, turn on pond pump; Press button D again, turn off pond pump.

Remote Controller Unlocks Electric Lock

Overview:

We manage a refrigerated ice storage. We are considering an application to remotely unlock the doors using an electric strike. The application would most likely use a remote with a range of less than 150 feet typically. I am interested in getting some information about components that you might have that would work for this application.

Solution:

We recommend 1 channel 2000m dc power output receiver (S1X-DC12-ANT2) and 1-button transmitter (CB-1). Input power and output power of receiver are same as dc 12v. So it is easy for wiring. Maximum working current is 10amp. Working distance of remote and receiver set is about 2000m (6000ft) in open field. The RF signal can pass through walls, doors and other obstacles.

Wire electric door lock and dc 12V power supply to the receiver accroding to the wiring diagram. Receiver is dc power output contact so you can connect door lock to A&B terminals. Electric door lock will get power from powered receiver.

Setting control mode Momentary: Only connect Jumper-1.

Press and hold big button: Turn on the relay, terminal A&B output DC power.

Release big button: Turn off the relay, terminal A&B no output.

When the door is locked, you can press and hold big button of the transmitter, the door will unlock.

RF Remote Control System is Applied at Private Airport

Overview:

“I am looking for a remote and multiple receivers for a small private airport. We have a controller box switch that activates when you key the microphone 7 times on a specific frequency. I would like to plug a dc power adapter into this unit and wire into one of your remotes. The runway lights are all solar dc leds. I will need 12 receivers total to start out. My question is: Can one remote, controlled by external wires, send a signal out to multiple receivers at the same time? In other words, if the remote detects dc input and sends out an ON signal, can several receivers receive the ON signal at the same time?”

Solution:

We recommend the low voltage triggered transmitter (CB-2V) and 1 channel 2000m receivers (S1L-DC12-ANT2). The most remarkable feature of this transmitter is low current triggered. That is to say, when you offer dc power 5~28V to this transmitter, it will send signal out to the receiver. The receiver is long range with external extended antenna. When it works in pairs with transmitter, their transmitting distance can reach 2000m (6000ft) in the open field. One transmitter can send out ON signal to make several receivers ON at the same time if you use the same code of those transmitter and receivers.

Wires on the transmitter should be connected to the contacts of original device which can generate dc 5~28V output power.

The normally open contacts B&C of receivers should be connected to solar led light being controlled. Wire each solar led light to each receiver.

When the contacts of two wires of transmitter input 5~28V voltage, the transmitter is triggered and then transmits an rf signal “ON” to the receiver. After the receiver receives the signal, contacts B&C are closed; the solar led lights being controlled are on.

When the contacts of two wires of transmitter’s power is cut, the transmitter is triggered and then transmits an rf signal “OFF” to the receiver. After the receiver receives the signal, contacts B&C are cut; the solar led lights being controlled are off.