momentary – Page 2 – Remote Control Everything

30amps 100M Remote Controller for Submersible Pump

Question from customer:

I am in Australia and here we have Live-Re and Neutral-Black and Earth-Green. I wish to wire a submersible pump to your radio controller then back to the consumer mains. Please advise if wiring would be.

Mains :

Live Red to Controller Power Supply L

Neutral Black to Controller Power Supply N

Controller terminal A to Pump Live Red

Controller terminal B to Pump Neutral Black

What is the terminal C in the controller used for? How is the earth cable from the pump and the incoming power cable earth to be connected via the controller?

Answer:

We recommend you 1 channel 30amps remote controller kit (S1PU-AC220&C-2). This 1 channel 30A rf remote control kit operates in toggle, momentary and latched control mode (set the mode as you like freely). It is great for hard to reach electrical devices, remote distance is 100m. Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

The outputs of this receiver are relay outputs (the terminals are normally open and normally closed), they are not AC power outputs. It just amount to a switch to turn on or off device.

If you want to turn on / off the pump by this product, the connections are as following:

Live Red to Controller Power Supply L

Neutral Black to Controller Power Supply N

Live Red to Controller terminal B

Neutral Black to Pump Neutral Black

Controller terminal A to Pump Live Red

the earth cable from the pump to Earth – Green

Usage:

Setting control mode Toggle: Only connect Jumper-2. Control mode Toggle: Press -> On; Press again -> Off. Press button 1: Turn on the submersible pump. Press button 1 again: Turn off the submersible pump.

Setting control mode Momentary: Only connect Jumper-1. Control mode Momentary: Press and hold -> On; Release -> Off. Press and hold button 1: Turn on the submersible pump. Release button 1: Turn off the submersible pump.

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2. Control mode Latched: Press -> On, other relays Off; Press another button -> Off. Press button 1: Turn on the submersible pump. Press button 2: Turn off the submersible pump.

How to Remote Control Linear Motion Actuator Run Forward and Backward

Question from customer:

I have 24V Linear Motion Actuator which moves 2 ways (OUT and IN). Also I have 24V power Supply.

I would like to connect the remote control, and be able to open and close the actuator. Ideally, I want to press the button until actuator extends fully, and press another button to retract fully.

Answer:

We recommend this 2 channel wireless remote control momentary on off switch which is widely applied to lights, motors, fans, electrically operated doors / locks / windows / blinds, etc. One relay as an ON/OFF switch can turn on or off electric gadget. If you want to remote control bidirectional motion, you may choose 2 channel remote (two relays). Your linear motion actuator can run forward and backward, so this remote is very available for you. It provides linear motion actuator with 10A. It is enough for linear motion actuator. With 2-button transmitter, its working distance reaches about 100m which can make your control range much wider, getting rid of narrow space constraint.

The wiring of linear motion actuator is a little sophisticated. See the following picture.

Initial state: A, B = Normally Closed; B, C = Normally Open.

So wire linear motion actuator to B terminals of two relays. Wire “C” terminals of two relays together to positive electrode of 24 batteries. Wire “A” terminals of two relays together to negative electrode of 24 batteries. And supply additional power to the receiver. It can avoid generating interfere between receiver and linear motion actuator.

Momentary mode is the only working mode in this remote. So press and hold button 1, linear motion actuator extends slowly, if you release button 1, it stops moving. Press and hold button 2, linear motion actuator retracts slowly, if you release button 2, it stops moving.

How to Remote Control 240V 25 amps Electric Equipment

Question from customer:

I am looking for an RF switch and transmitter where the switch has a coil voltage up to 12v and the switch terminal can handle 240v and 25 amps. Do you have anything like this?

Answer:

We recommend 1 channel high power remote controller (S1PU-DC12&C-2). The receiver is normally open and closed contact, so you can wire the gadget which is activated by AC 110~240V or DC0~28V. The relay outputs 30amps current for gadget. It meets your needs. The receiver is run by 12VDC, but receiver and controller gadget will be supplied power separately so that they won’t interfere to each other. The transmitter is 2-button type remote. When it works with receiver together, their working distances reach 100m.

Here is the sample of wiring method.

Suppose that we remote control a lamp. The normally open terminals are A&B. The normally open terminals are A&C. Lamp should be connected to A&C terminals. Normally open and closed contact is similar with an ON/OFF switch. The being controlled gadget cannot get power from powered receiver. We should supply additional power to it. We can supply DC or AC power to controlled gadget according to its available power supply.

Toggle mode, momentary mode and latched mode are its working modes.

Setting control mode Toggle: Only connect Jumper-1.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on the gadget

Press button 1 again: Turn off the gadget

Setting control mode Momentary: Only connect Jumper-2.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on the gadget

Release button 1: Turn off the gadget

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: Turn on the gadget

Press button 2: Turn off the gadget

Remote Control Crystal Glass Panel Doorbell Switch

Question from customer:

I want to use your remote control system control an electromechanical bell. Do you have any kind of remotes suitable?

Answer：

We recommend 1 channel momentary remote kit and doorbell touch switch to you make a wireless doorbell. This 1 channel dc rf remote control momentary switch is with direct power output function. The input and output power are the same. It is easier for wiring and operation and widely applied to control lights, motors, fans, electrically operated doors / locks / windows or other electrical devices. Doorbell touch switch is quick and easy to install, as normal light switch.

How to make them work? Let’s read the following procedure.

The first step, you may solder two terminals of 1-button transmitter backside to doorbell switch “L1&L” terminals backside.

And next, your doorbell should be connected to the receiver like the diagram. Connect doorbell to “A&B” terminal. Then switch on power.

Finally, press the button on switch outdoor, is equivalent to press button of transmitter. The transmitter will send RF signal to receiver. Then, the bell will ring. So it makes a wireless doorbell.

10A Motor Remote Controller for Hoist

Question from customer：

I have a ceiling mounted 110v hoist that I need to control wirelessly. It is currently controlled by hanging pendants. Please advise at to the proper wireless system.

Answer：

We recommend the model of AC 100~240V Motor Momentary Remote Control (S1FM-AC220+1CV-2-2) to you. It is specially designed for controlling motor of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors, hoist or other appliances and mechanicals. With universal power input, it supports voltage of AC 100V-240V, which can be widely used in many countries, such as the U.S, Canada, UK and France.

Connect live wire to terminal “L” and neutral wire to terminal “N”. Then connect AC motor of hoist to terminals “UP”, “COMMOM” and “DOWN” directly. Or you can control your hoist through controlling hanging pendants. You can exchange “UP” and “DOWN” wires of motor to change the rotating direction of motor.

1. Remote Controlling by transmitter:

Press and hold button ▲ on remote : Terminals UP and COMMOM directly output AC110V / AC220V; motor rotates continuously in positive direction.

Release button ▲ on remote : Stop the motor.

Press and hold button ▼ on remote: Terminals DOWN and COMMOM directly output AC110V / AC220V; motor rotates continuously in reversal direction.

Release button ▼ on remote : Stop the motor.

2. Remote Controlling by manual button on the receiver:

Besides the controlling with transmitter, you can also control device with manual button on the receiver. Controlling

Note: Button ■ on receiver is useless.