momentary mode – Page 2 – Remote Control Everything

Motor Remote Controller and Contactor Remote Control Winch

Question from customer:

Hi, I am looking for a 110 volt remote control for a winch that pulls my boat from the water into my boat house.

Requirements:

120 volt

20 amps max

Momentary switches

Do you have a kit that meets these requirements?

Answer:

First, we’d like to recommend motor momentary remote controller (S1FM-AC220&CV-2-2). It can remote control motors of rolling blinds/ doors, projection screens, awnings, pumps, winches, conveyors or other electric appliances and machineries. With 2 directive buttons ▲(Positive rotation) and ▼(Reversal rotation), you can rotate the motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance(this kind of remote controller is 500m/1500ft). Power supply is AC 100~240V. But this maximum current is 10amps, it is not enough for you to remote control your 20amps winch. So we’d like show you contactor motor starter relay, you can use it amplify current which you need. AC contactor (aka motor starter) is a high capacity relay. It is often used to control a motor or as a main power switch. It’s used for long range connection and circuit disconnection, frequent activation and controlling AC motor.

Here is the wiring diagram. Two contactors will act as a bridge between remote controller and high power motor to help activate high power motor to rotate in positive and reversal position.

Wire A1 terminal of contactor 1 to UP terminal of receiver, and A1 terminal of contactor 2 to DOWN of receiver. Wire T2 terminals of contactors 1&2 to winch motor. Wire winch motor to COM terminal of receiver. Supply power to receiver and contactor 1&2 respectively.

Operation:

Press and hold button ▲ on remote: Motor rotates continuously in positive direction.

Release button ▲ on remote: Stop the motor.

Press and hold button ▼ on remote: Motor rotates continuously in reversal direction.

Release button▼ on remote: Stop the motor.

How to Remote Control Horn

Question from customer:

I would like some help to make my Horn starting system become remote controlled. At present I have a momentary switch on a 12 foot cable when the switch is press it activates the horn. I would like the horn and housing to be separated. I would like the horn to be approximately 100M away. Which of your products will help me? In the future I would like to add a 2nd and 3rd horn to my set up which will be housed in separate boxes.

Answer:

If you want to remote control a horn, we recommend the long range 1 channel 12V momentary receiver (S1XM-DC12-ANT2) and the long range transmitter CB-1. It is direct power output; control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. Its working distance can reach 2000m with external extended antenna.

Here is the wiring diagram. Wire horn to A&B terminals and supply 12V power to the receiver. There is no need to supply additional power to horn because horn can get power from powered receiver.

After wiring, here comes the operation. Momentary mode is the only working mode in it.

Press and hold button: Turn on the horn; Release the button: Turn off the horn.

If you want to remote control 2~3 horns, we recommend 2~3 receivers S1XM-DC12-ANT2 and another two transmitters, one is two-button long range transmitter CB-2 or three-button long range transmitter CB-3.

100M 1CH Momentary Remote Control AC Motor

The 1 channel RF Momentary Remote Control (S1M-AC110~240V & C-1) features in AC110V ~220V. There are two kinds of receiver style, one is AC 110V (AC 100~120V), widely used in US, Canada…; the other is AC220V (AC 200~240V), used in UK, France…. The Coding type of receiver is learning code. Maximum working current for each channel is 3 ampere. The working distance is 100M in the open air. Momentary mode is the only working mode of this remote.

We can use this kind of remote control to control AC motor on and off. For instance, the garden irrigation system, hot water circulation system, water pump and so on. Those motors just need to be turned on and off.

Look at the following wiring diagram. From the interior analogue circuit, we connect the neutral wire to the terminal “1”, and the live wire to the terminal “2”. And then connect the motor to the terminal “5” and the neutral wire.

Momentary mode (Press and hold button -> On; Release button -> Off)) All you need to do is just press and hold slightly the button on the remote. You press and hold button to turn on motor; release button to turn off motor.

Momentary Remote Switch for Car Siren and LED Lights

Question from customer:

If I wire a 12v device into the receiver, I won’t need to connect the device to its own power source. It gets power through this receiver. Actually,I am ready to wire a 12v car siren into one channel and a set of 12v LEDs into the other, and wire the 12v DC in to my cars battery. I can honk the siren and flash the lights from the remote?

Answer:

Our suggestion is that you can choose our 2 channel momentary 12VDC power output remote controller (S2XM-DC12 & C-2).

This is 12VDC direct power output, that is to say, you don’t have to supply your siren and led lamps to its own power because they can get through this receiver if you supply power to receiver. In addition, there are two channels for your devices you want to control. It is momentary controlling mode, which means that you press and hold button, the siren blares or led lamps flash constantly, but you release button, siren stops blaring or led lamps stop flashing. Two buttons on the transmitter are controlled siren and led lamps respectively. They won’t be interfered each other.

You can follow the wiring diagram and picture to wire your siren and led lamps. Car horn is connected to terminals of relay 1 and led lamps are connected to terminals of relay 1 in parallel. Car battery is supplied to receiver. Thus, siren and led lamps can get power through receiver.

You can honk the siren by pressing button 1 on the transmitter and flash led lamps by pressing button 2 on the transmitter. One transmitter can control two or more devices at ease.

How to Remote Control Screens

Question from customer:

We require an RF remote controller with 2 channel output 24v dc power supply to control screens. Then it can be operate nearly 35 meters. Remote controller can operate when we press remote button. When we release the remote button, remote controller will not operate.

Answer:

We recommend you the model of 2 channel direct power output momentary remote controller (S2XM-DC24+C-2). The operating voltage is 24V. The working distance is 100m. Direct power output; control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. It is momentary working mode. Momentary mode can be set to control rolling blind or rolling door. You need to press and hold the button of remote to make the blind or door open/close. Momentary mode is motivated by single relay, which means you can work these two modes with single button remote.

Wiring:

Screen 1 is connected to the A&B terminals of OUTPUT 1. Screen 2 is connected to the A&B terminals of OUTPUT 2. The receiver can be supplied 24V power supply.

Usage:

Press and hold button 1: Turn on the relay 1, switch on screen 1.

Release the button: Turn off the relay 1, switch off screen 1.

Press and hold button 2: Turn on the relay 2, switch on screen 2.

Release the button: Turn off the relay 2, switch off screen 2.