500m – Page 3 – Remote Control Everything

9V Remote Control for Electron Microscope’s Motor

Question from customer:

I use a manual switch to control 4 9V motors of my electron microscope and each motor works in 150ma (0.15a). In addition, only one motor works when I press button of remote control each time. Now I want to remote control them, have you got any suitable remote for me?

Electron microscope:

Manual Switch of microscope:

Answer:

We thought this 8 channel rf remote transmitter & receiver is very suitable for you . It can be used to control at most 8 on / off electrical devices. With characteristics of strong anti-interference, reverse power protection and over current protection. Three voltages dc9v, dc12v and dc24v are provided to choose. It is widely applied to control many kinds of lights, electrically operated doors / gates / windows / blinds and so on. It works with 8-button transmitter and their transmitting distance can reach to 500m.

This is the wiring diagram.

Wire each motor to the normally open terminal “B”. According to the diagram, you can do wiring like above. Even though there are 8 working modes in it, you can choose ”Momentary mode” which is applied in motor’s rotation.

Control mode Momentary (Channel 1~8): Press and hold -> On; Release -> Off.

Press and hold button 1: Motor 1 rotates in positive direction

Release button 1: Motor 1 stops rotation

Press and hold button 2: Motor 1 rotates in reverse direction

Release button 2: Motor 1 stops rotation

Press and hold button 3: Motor 2 rotates in positive direction

Release button 3: Motor2 stops rotation

Press and hold button 4: Motor 2 rotates in reverse direction

Release button 4: Motor 2 stops rotation

Press and hold button 5: Motor 3 rotates in positive direction

Release button 5: Motor 3 stops rotation

Press and hold button 6: Motor 3 rotates in reverse direction

Release button 6: Motor 3 stops rotation

Press and hold button 7: Motor 4 rotates in positive direction

Release button 7: Motor 4 stops rotation

Press and hold button 8: Motor 4 rotates in reverse direction

Release button 8: Motor 4 stops rotation

Only one motor works when you press the corresponding button on the remote.

500M Toggle Transmitter Remote Control 4 Lamps in House

Question from customer:

I’m looking for a wireless remote that I can use to create a simple on off switch to 4 AC lights fixtures for living room, bed room, kitchen, shower room’s illumination. Do you have a recommendation for which wireless remote or RF transmitters may be better choice for this task?

Answer:

We recommend model 4Channel AC110V~220V Remote Controller – 1 Transmitter & 4 Receivers (4S1T-AC110/220V+CV-4). The AC RF remote control switch system, which is one transmitter pairs with four receivers. With about 500 meters range (theoretically), it can widely used in lights / lamps , motors, fans, cameras, video signals, audio signals, garage doors, electric shutter doors, telescopic doors, windows, cars, etc. This remote control has a toggle control mode which is the only working mode in it. It is a low cost remote control with high quality. Extremely easy to install and use. The maximum current is 3 ampere each channel.

The light wiring is fairly simple.

Connect the neutral wire to the terminal “1”, and the live wire to the terminal “2”. Connect the lamp to the terminal “5” and the neutral wire. S o you can wire your lamps to each receiver one by one.

Operation procedure:

1) Press button 1, turn on the lamp of receiver 1. Press button 1 again, turn off the lamp of receiver 1.

2) Press button 2, turn on the lamp of receiver 2. Press button 2 again, turn off the lamp of receiver 2.

3) Press button 3, turn on the lamp of receiver 3. Press button 3 again, turn off the lamp of receiver 3.

4) Press button 4, turn on the lamp of receiver 4. Press button 4 again, turn off the lamp of receiver 4.

Holding one transmitter, you can wireless remote control your any controlled lamps of house easily because the wireless signal can pass through walls, floors and doors with reliable distance.

6 One Channel Receivers and One Transmitter for 6 Lights

Question from customer:

I am about to install a solar panel in a small beach house to give 6 lights, I was thinking of using your remote controls. I need one remote for all 6 lights. What I need for this it is all 12 voltage.

Answer:

We recommend you to use one 500M transmitter with 6 DC receivers (6S1XB-DC12+CV-6). It is “One to many series” which includes one-transmitter-to-many-receiver system and one-receiver-to-many-transmitter system. It is often used for controlling two or more electrical devices in different places by one remote; or one electrical device by two or more remote. Here is one transmitter to 6 receivers. The receiver is 12V direct power output so there is no need to supply power to the device which is connected to the receiver. Its working distance is about 500m in the open field.

The wiring procedure is fairly simple. Lights are wired to A&B terminals (+and -) of receivers one by one. Then you supply 12V power to each receiver respectively. So it works.

Toggle, Momentary, Latched modes are presented here. You’d better set toggle mode.

Only connect Jumper-2.

Press button 1, turn on light 1.

Press button 1 again, turn off light 1.

…

Press button 6, turn on light 6.

Press button 6 again, turn off light 6.

One Transmitter Remote Controls 12 Christmas Decorative LED Lamps

Question from customer:

When Christmas Day comes, people always use LED lights to decorate house or Christmas trees. So I’m looking for a wireless remote that I can use to create a simple on off switch to 12 led light fixtures connecting to a 12V battery at different places around my home. That souds a good idea, right? Do you have a recommendation for which Wireless remotes or RF transmitters may be the best for the task at hand?

Answer:

We recommend model 12 Channel DC12V Remote Controller – 1 Transmitter & 12 Receiver (12S1UB-DC12&1CV-12). This RF remote controller has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. That is to say, you only need a transmitter to control 12 receivers. It operates in toggle, momentary, and latched mode (set the mode as you like freely). It is great for hard to reach lights or other DC/AC electrical devices, remote distance can be 500m (theoretically). And it is applied for controlling lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

Here is the wiring diagram. LED lamp is connected to normally open terminals B&C. And add a wire between terminals “B&-“ and another wire to terminals “C&+”. At last, wire a plug to terminals “+&-“.

It’s easy to set and operate. You can press each button on the transmitter to control the corresponding receiver to control LED lamp. The receiver can learn at most 60 different codes for remote controlling.

AC Motors are Controlled by DC Remote

Nowadays, motors are found in applications as diverse as industrial fans, pump, household appliances, tools and other devices, which can be powered by direct current (DC) or alternating current (AC) source. Of course, we can also remote control motors of those devices above to switch on or off of devices, even the forward-reverse rotation. When you want to control many motors with one transmitter, we think multi-channel remote control is very favorable.

8 channel dc triggered RF remote transmitter & receiver operates in 8 working modes. It can be used to control at most 8 on / off electrical devices. With characteristics of strong anti-interference, reverse power protection and over current protection. Three voltages dc9v, dc12v and dc24v are provided to choose. It is widely applied to control every kind of lights, electrically operated doors / gates / windows / blinds and so on.

Would you like know how to control 2 ac motors with an 8-channel dc triggered remote? Look at the following show.

First off all, we prepare material.

1×8CH rf receiver

1×8-button transmitter

2×AC motor

Some lines

Power supply 220V

Here is the wiring diagram. This is the AC motor’s wiring. Motors should be connected to common terminals of B. We add neutral wires to connect both motors since they are ac motors. Live wires are connected to normally open terminals of C.