30amps – Remote Control Everything

How to Remote Control 4 High Power Receiver with 1 Transmitter

We’d like to recommend one-to-many series: 4 channel 30amps AC RF remote control gadget (4S1PUA-AC220+1CV-4), which includes 1 transmitter and 4 receivers. The transmitter’s transmission distance is 500m/1500ft theoretically. It is designed for high power device. Then maximum current is 30amps. This wireless gadget can remote control high power lights, TVs, motors, fans, cameras, video signals, audio signals, electrical operated doors/locks/windows/blinds/cars or other appliances with voltage of AC 110~240V or DC0~28V.

One transmitter can remote control 4 receivers simultaneously. If you want to use two or more receivers in the same place, you can set them with different codes. It operates in three modes, including toggle, momentary and latched. All working modes can be switched easily by connecting or disconnecting jumper.

We’d like to show how to remote control ac, dc lamps or ac motor.

The contact of relay of each receiver is normally open/ closed. So you need to wire dc lamp to normally open contact B&C and supply DC 12V power to lamp. When you want to remote control ac motors or lamps, you can wire them to receivers as mentioned above. But ac motor and lamps can share the same power supply if you wire as the right picture shown.

Operation:

Setting control mode Toggle: Only connect Jumper-2.

Control mode Toggle: Press -> On; Press again -> Off.

Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Press button 1 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Press button 2 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Press button 3 again: Turn off the relay (disconnect A and B, connect A and C)

Press button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Press button 4 again: Turn off the relay (disconnect A and B, connect A and C)

Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary: Press and hold -> On; Release -> Off.

Press and hold button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Release button 1: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Release button 2: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Release button 3: Turn off the relay (disconnect A and B, connect A and C)

Press and hold button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Release button 4: Turn off the relay (disconnect A and B, connect A and C)

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On; other relays Off; Press another button -> Off.

Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 2, 3, 4 (disconnect A and B, connect A and C)

Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 3, 4 (disconnect A and B, connect A and C)

Press button 3: Turn on the relay of the receiver 3 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 2, 4 (disconnect A and B, connect A and C)

Press button 4: Turn on the relay of the receiver 4 (connect A and B, disconnect A and C)

Turn off the relay of the receiver 1, 2, 3 (disconnect A and B, connect A and C)

How to Control Linear Actuator by Remote Transmitter and Manual Switch

30 amps dc output controller (S1PF-DC12-ANT2+CB-4) is designed for motor controlling. It is compatible with many kinds of motor which is actuated by DC 12V/24V. It is applied to DC motors of rolling blinds / doors, projection screens, awnings, pumps, winches, conveyors or other appliances. We add external extended antenna to the receiver, so we make its transmitting distance reach to 2000m (6000ft) in the open field. The receiver pairs up with a 4-button transmitter and has manual switches on itself. Both transmitter and manual switches can send signal to receiver.

Let’s show you how to control 12V DC linear actuator with transmitter and manual switch.

Here is the material.

1×receiver: S1PF-DC12-ANT2

1×transmitter: CB-4

1×12VDC Linear Actuator Motor

Power supply : 12VDC 3A Power Adapter

Wiring is simple. You should wire linear actuator to OUTPUT terminal of receiver.

Setting control mode Latched: Connect Jumper (CN1)

Press button “A”, motor shaft extends

Press button “C”, motor shaft retracts

Press button “B” or ‘D”, motor stops

Manual Switch (Latched mode)

Press “S1″, motor shaft extends

Press “S3″, motor shaft retracts

Press “S2″, motor stops

Setting control mode Momentary: Do not connect Jumper

Press and hold button “A”, motor shaft extends; Release button “A”, motor stops

Press and hold button “C”, motor shaft retracts; Release button “C”, motor stops

Manual Switch (Momentary mode)

Press and hold button “S1″, motor shaft extends; Release button “S1″, motor stops

Press and hold button “S3″, motor shaft retracts; Release button “S3″, motor stops

www.ourautomation.com

30amps 100M Remote Controller for Submersible Pump

Question from customer:

I am in Australia and here we have Live-Re and Neutral-Black and Earth-Green. I wish to wire a submersible pump to your radio controller then back to the consumer mains. Please advise if wiring would be.

Mains :

Live Red to Controller Power Supply L

Neutral Black to Controller Power Supply N

Controller terminal A to Pump Live Red

Controller terminal B to Pump Neutral Black

What is the terminal C in the controller used for? How is the earth cable from the pump and the incoming power cable earth to be connected via the controller?

Answer:

We recommend you 1 channel 30amps remote controller kit (S1PU-AC220&C-2). This 1 channel 30A rf remote control kit operates in toggle, momentary and latched control mode (set the mode as you like freely). It is great for hard to reach electrical devices, remote distance is 100m. Control lights, motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances with voltage AC110~240V or DC0~28V.

The outputs of this receiver are relay outputs (the terminals are normally open and normally closed), they are not AC power outputs. It just amount to a switch to turn on or off device.

If you want to turn on / off the pump by this product, the connections are as following:

Live Red to Controller Power Supply L

Neutral Black to Controller Power Supply N

Live Red to Controller terminal B

Neutral Black to Pump Neutral Black

Controller terminal A to Pump Live Red

the earth cable from the pump to Earth – Green

Usage:

Setting control mode Toggle: Only connect Jumper-2. Control mode Toggle: Press -> On; Press again -> Off. Press button 1: Turn on the submersible pump. Press button 1 again: Turn off the submersible pump.

Setting control mode Momentary: Only connect Jumper-1. Control mode Momentary: Press and hold -> On; Release -> Off. Press and hold button 1: Turn on the submersible pump. Release button 1: Turn off the submersible pump.

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2. Control mode Latched: Press -> On, other relays Off; Press another button -> Off. Press button 1: Turn on the submersible pump. Press button 2: Turn off the submersible pump.