2000M – Page 3 – Remote Control Everything

6V Output RF Remote Control System Apply for Device Control Another Device

Question from customer:

I want a remote controlling unit that the transmitter is to function as a switch to the receiver activated by supplying a 12V DC current to the transmitter (switch it on). The receiver then allows a 6V DC current to be supplied to a designated appliance. When the transmitter is shut off the receiver will shut down.

Answer:

Maybe this kind of controlling unit —6V power direct output RF remote control system (S1XL-DC06-ANT2+CB-2V) is suitable for you. It is activated directly by 6V power supply. You don’t have to supply additional power to the device being controlled because the controlled device will get power from powered receiver. It is specially designed for device controlling another device. The remarkable characteristic of the transmitter CB-2V will be triggered by DC power 5~28V input. We add external extended antenna which makes transmitting distance up to 2000m.

According to the picture above, he wants the transmitter can be activated by manual switch and turn receiver on/off when the current in that circuit is on/off. First, the transmitter is supposed to be connected to power supply and that manual switch. Second, designated appliance should be connected to receiver.

We prepare a demonstration for this practical use.

We switch on the manual switch and the transmitter will send an “ON” signal to the receiver. The receiver receives the signal to instruct the light to turn on. We switch off the manual switch and the transmitter will send an “OFF” signal to the receiver. The receiver receives the signal to instruct the light to turn off.

Momentary 6V 1 Channel Remote Controller for Doorbell

Question from customer:

I want to install a single channel remote to control my doorbell within the range of 150m. The old 6V doorbell was broken and I don’t want to repair the wires of doorbell. Ordinary wireless doorbell cannot be used because it doesn’t reach the distance I really want. I have an idea that a transmitter is connected to the doorbell button and relay in receiver is connected to doorbell. The only problem is the control range of remote need to reach about 150m. Would you like to recommend some favorable products?

Answer:

We recommend the 6V one channel 2000m receiver(S1U-DC06-ANT2) and long range transmitter (CB-1). Working voltage range of receiver is 6V. With normally open and close terminal, the voltage of the device being controlled is AC110~240V or DC0~28V. So it can be applied in 6V doorbell. Usually, you don’t have to supply additional power to doorbell because it can get 6V power from powered receiver when you connect them to the 6V power supply together. And the most significant is that it has extended external antenna which makes its control range up to 2000m (6000ft). You will be satisfied with this product.

According to your requirement, you can connect the button of the bell to the transmitter by two wires. Then connect the bell to the relay in the receiver.

Setting control mode Momentary: Connect Jumper-1.

When you press the button of the bell, RF signal will be sent out from transmitter to receiver. The receiver receives to turn on the relay, then the doorbell rings. Release the button, the doorbell stops ringing.

How to Remote Control Horn

Question from customer:

I would like some help to make my Horn starting system become remote controlled. At present I have a momentary switch on a 12 foot cable when the switch is press it activates the horn. I would like the horn and housing to be separated. I would like the horn to be approximately 100M away. Which of your products will help me? In the future I would like to add a 2nd and 3rd horn to my set up which will be housed in separate boxes.

Answer:

If you want to remote control a horn, we recommend the long range 1 channel 12V momentary receiver (S1XM-DC12-ANT2) and the long range transmitter CB-1. It is direct power output; control lights, motors, fans, electrically operated doors/locks/windows/blinds/cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors. Its working distance can reach 2000m with external extended antenna.

Here is the wiring diagram. Wire horn to A&B terminals and supply 12V power to the receiver. There is no need to supply additional power to horn because horn can get power from powered receiver.

After wiring, here comes the operation. Momentary mode is the only working mode in it.

Press and hold button: Turn on the horn; Release the button: Turn off the horn.

If you want to remote control 2~3 horns, we recommend 2~3 receivers S1XM-DC12-ANT2 and another two transmitters, one is two-button long range transmitter CB-2 or three-button long range transmitter CB-3.

Heavy Duty 30A Remote Controller for Concrete Pump

Question from customer:

I need a one channel, 12 volt, one button toggle on off switch, heavy duty for outdoor wet, dusty rough vibrating conditions. This devise will be mounted on a concrete pump and will need to operate from a distance of 200m with obstructions.

Answer:

We thought that you should have high power and long distance remote controller. We recommend this 30 ampere multi-mode long range remote control (S1PU-DC12/24-ANT2 & CB-2). This 1 channel 30A long range remote control operates in toggle, momentary and latched mode (set the mode as you like freely). It can be used to control lights, motors, electrically operated doors / locks / windows / blinds / cars or other appliances with AC110~240V or DC0~28V. With external extend antenna, the transmitter and receiver have longer working range, up to 2000M.

Now we’d like to show you how to remote control 12V concrete motor. See the wiring diagram below, B is normally open terminal; C normally closed terminal and A common terminal. Connect motor to Terminal A&B. And motor and receiver will share the same power supply as the following diagram.

2000M Remote Controller Controls Garage Door Automatically

Question from customer:

I need a radio system for switching a receiver of an underground garage, by a concrete slab with steel reinforcement and about 30 meters Distance 1st floor. The receiver may be 220 volts. Transmitter I want to act with an external contact. (Connection to a car alarm system).

Answer:

We recommend the 1 channel high power receiver (S1PUA-AC220-ANT2) and long range transmitter with extended wires (CB-2N). The receiver is activated by ac 220V, which is about 2000m working distance with external extended antenna. The wireless RF signal can pass through walls, floors and doors. It works with the long range transmitter, which features in two external wires because connection of two wires is its triggering method.

According to your requirement, we drew a wiring diagram.

Wires on the transmitter should be connected to the contacts of car alarm system.

The normally open contacts A&B of receiver should be connected to the garage door motor. And supply additional 220V power other than receiver.

Setting latched mode to this receiver.

When the contacts of two wires are closed, the transmitter is triggered and then transmits an rf signal “ON” to activate the receiver. After the receiver receives the signal, contacts A&B are closed; the motor starts to work to open the garage door.

When the contacts of float switch are cut, the transmitter is triggered and then transmits an rf signal “OFF” to deactivate the receiver. After the receiver receives the signal, contacts A&B are cut; the motor stops working to shut down the garage door.