2000M – Page 2 – Remote Control Everything

Motion Triggered Detector and Time Delay Function Receiver Operation

Question from customer:

What we need is three motion sensors with 2 receivers. The receiver can be one channel. Once there is a trigger to any one motion sensor this will trigger both receivers at the same time. Each receiver can have one dry contact output that will trigger anytime any of the motion sensors trigger. And the receiver will go back to previous state after 1 minute.

Answer:

We recommend rf remote receiver and infrared motion sensor (S1DA-DC12-ANT2+W-01) to you. You can have those 2 receivers paired up with three motion sensors so that they can work together. The receiver is delay time adjustable (0 seconds ~ 99 hours). It controls lights, motors, fans, electrically operated doors/locks/ windows/ blinds/ cars or other appliances. You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless signal can pass through walls, floors and doors. With the extended external antenna, its working distance can reach 2000m.

The receiver is normally open and close dry contact. So the device which you want to remote control can be supplied with additional power supply according to your device’s voltage parameter. Wire device to normally open dry contact.

Press buttons of “＋” and “－” on the timer, adjust delay time from 0 second to 99 hours. “H” is Hour, “M” is Minute, and “S” is Second. If you want it go back to previous state after 1 minute, you can set “M 0 1”, it means the delay time is 1 minute. When some movements trigger the motion sensor, turn off the relay and turn on device. After 1 minute, it is that the receiver will change status immediately if there is no trigger but will return to previous state after 1 minute. The device is turned off automatically.

Any of the motion sensors can trigger that receiver. If you use those two receivers in the same place, you can set them with different codes.

One Command from Transmitter Activates Four Devices Off or On at Remote Receiver

Sometimes, you want to remote control more than one electric devices just with one transmitter，but most of remote control systems only allow one command at a time to remote control one device even though they are able to activate 2 or more relays. Or you are just looking for a remote control system with range of only 100m that will allow the activation of least three or four commands simultaneously and then trigger three or four channels on the receiver at the same time.

Actually, you thought can be realized if the 4 channel 12VDC long range receiver’s interior circuit can be changed and pair with 1-button transmitter. You just need only one button on the transmitter that you can remote control 4 devices. Its working distance is beyond your thought. It can reach 2000m (no obstacles).

You wire either AC 110~240V or DC0~28V electric devices to receiver because of its normally open and closed contact terminals. Electric devices usually wire to normally open terminals for safety purpose. Especially, if it is ac power activated remote control receiver. Receiver and controlled devices will not share the same power supply from the following wiring.

On the other hand, if you want to wire dc motivated device, such as led lights or dc motors, you can look at the following wiring diagram for your reference. Motors will share the same power supply with the receiver.

When you press the button on the transmitter CB-1, it will trigger 4 relays on the receiver at the same time. As thus, four electric gadgets will be turned on at the same time once receiver received command. When you press the button again, turn off four electric gadgets simultaneously.

2000m Tri-mode Motor Remote Controller for Skylight

Skylights are widely used in designing for residential, public, and commercial buildings. Increased day lighting can result in less electric lighting use and saving energy, lowering costs and reducing environmental pollution. Skylight can offer you beautiful view from roof. At night, you can also watch stars from skylight when you stay in bed. Maybe it is not convenient to you to open and close skylight manually. So you may want to remote control it.

Tri-mode motor remote controller with 3-button transmitter can be used in dc motor of skylight application. Applications also include light remote control, electric gate remote control, electric window / blind remote control, etc. It is added an external extended antenna, which makes its transmitting distance reach 2000m.

There are three working modes in it. You will see the example controlling procedure from following information.

Material preparation:

Wiring is very simple.

Motor is wired to B terminals of receiver. And supply power for receiver. Motor can get power from receiver.

Setting control mode Toggle: Only connect Jumper-2.

Press button A, motor rotates in the positive direction; Press button A again, motor stops

Press button B, motor rotates in the reversal direction; Press button B again, motor stops

Setting control mode Momentary: Only connect Jumper-1.

Press and hold button A, motor rotates in the positive direction.

Release button A, motor stops

Press and hold button B, motor rotates in the reversal direction.

Release button B, motor stops

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button A, motor rotates in the positive direction.

Press button B, motor rotates in the reversal direction.

Press button C, motor stops

Video, please click here

4 Channel 12VDC Remote Control Kit for Lights

Question from customer:

I need a four channel receiver and transmitter to control lights or LEDs at 300 meters, 12 volt DC power. Do you have a system? Please respond as soon as possible. Large quantities are possible if we can find the right controlling system.

Answer:

4 channel 12VDC Power Output Switch Kit (S4X-DC12-ANT2&CB-4L) is your better choice. 4 lights or LED lamps can be wired to its channels. And 4 lamps can get power directly from the powered receiver. It is very convenient to you because you don’t have to supply additional power to lights. 2000m can be reached in the open field with the external extend magnetic antenna. Besides controlling lights, it can be applied to many fields, such as motors, fans, electrically operated doors / locks / windows / blinds / cars or other appliances.

Here is the wiring diagram. It is simple to wire lights. Wire four lights to A&B terminals from relay 1 to relay 4. Supply 12VDC to the receiver.

There are four working modes in this kit. They are toggle, momentary, latched, momentary + toggle modes.

Setting different control modes

•1) Setting control mode Toggle: Only connect Jumper-2.

Press button A: Turn on the relay 1, terminal OUT 1 (A&B) outputs DC power.

Press button A again: Turn off the relay 1, terminal OUT 1 no output.

Press button B: Turn on the relay 2, terminal OUT 2 (A&B) outputs DC power.

Press button B again: Turn off the relay 2, terminal OUT 2 no output.

……

•2) Setting control mode Momentary: Only connect Jumper-1.

Press and hold button A: Turn on the relay 1, terminal OUT 1 (A&B) outputs DC power.

Release button A: Turn off the relay 1, terminal OUT 1 no output.

Press and hold button B: Turn on the relay 2, terminal OUT 2 (A&B) outputs DC power.

Release button B: Turn off the relay 2, terminal OUT 2 no output.

……

•3) Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.

Press button A: Turn on the relay 1, terminal OUT 1 (A&B) outputs DC power.

Turn off the relay 2, terminal OUT 2 no output.

Press button B: Turn on the relay 2, terminal OUT 2 (A&B) outputs DC power.

Turn off the relay 1, terminal OUT 1 no output.

……

•4) Setting control mode Momentary (Channel 1~2) + Toggle (Channel 3~4): Connect Jumper-1 and Jumper-2.

30A High Power Remote Switch for Fireplace Chimney Fan

Question from Customer:

I’m looking for solution to remotely control fireplace chimney fan on roof of hi-rise building. Desired range would by over 150- 300ft. Fan is 110v, around 2A. Power source would be on roof and antenna would be on roof.

Please let me know if you have hardware solution.

Answer:

1 channel 30A long range remote switch (S1PX-AC220-ANT2&CB-2) is very suitable for you. With 30A current and AC100~240V voltage direct output, you don’t have to provide additional power supply to controlled fireplace chimney fan because it can get power from powered receiver. The receiver is installed a external extend magnetic antenna, it will help receiver to amplify RF signal reception so that its working distance can reach 2000m(6000ft) outdoor. It is applied to hi-rise building and long range between two buildings. The transmitter enhances its transmitting function to match this kind of receiver.

The wiring procedure is simple. Look at the following picture. Wire fan’s motor to L&N terminals of receiver. Supply 110v to receiver.

There are toggle, momentary, latched modes in it. Among three modes, we suggest you to use latched mode (Do not connect Jumper-1 and Jumper-2.)

Press big button: Turn on the fireplace chimney fan.

Press small button: Turn off the fireplace chimney fan.