2 channels – Remote Control Everything

How to Remote Control Linear Motion Actuator Run Forward and Backward

Question from customer:

I have 24V Linear Motion Actuator which moves 2 ways (OUT and IN). Also I have 24V power Supply.

I would like to connect the remote control, and be able to open and close the actuator. Ideally, I want to press the button until actuator extends fully, and press another button to retract fully.

Answer:

We recommend this 2 channel wireless remote control momentary on off switch which is widely applied to lights, motors, fans, electrically operated doors / locks / windows / blinds, etc. One relay as an ON/OFF switch can turn on or off electric gadget. If you want to remote control bidirectional motion, you may choose 2 channel remote (two relays). Your linear motion actuator can run forward and backward, so this remote is very available for you. It provides linear motion actuator with 10A. It is enough for linear motion actuator. With 2-button transmitter, its working distance reaches about 100m which can make your control range much wider, getting rid of narrow space constraint.

The wiring of linear motion actuator is a little sophisticated. See the following picture.

Initial state: A, B = Normally Closed; B, C = Normally Open.

So wire linear motion actuator to B terminals of two relays. Wire “C” terminals of two relays together to positive electrode of 24 batteries. Wire “A” terminals of two relays together to negative electrode of 24 batteries. And supply additional power to the receiver. It can avoid generating interfere between receiver and linear motion actuator.

Momentary mode is the only working mode in this remote. So press and hold button 1, linear motion actuator extends slowly, if you release button 1, it stops moving. Press and hold button 2, linear motion actuator retracts slowly, if you release button 2, it stops moving.

2 Channel Remote Control 2 Lights in Basement

Recently, one of our customer wrote to us that she wanted to remote control two lights in the basement from the first floor. But she was afraid that the scope of the transmitting was too large. She could not control those lights leisurely and carefree. She asked us about suggestion.

We would like to recommend this kind of 2 channel long range remote control with external magnetic mount antenna.

At first, you can do some wiring according to our application circuit.

Operation:

You can choose “Toggle Mode”. Only connect Jumper-2.

Press big button: Turn on the light 1. Press big button again: Turn off the light 1.

Press small button: Turn on the light 2. Press small button again: Turn off the light 2.

That is so easy to operate.

Firework Ignitor System for launching 2 Electric Igniters Remotely

Beautiful fireworks burst in the night. Usually, we use manual ignitor to ignite fireworks. It is so dangerous for us to ignite firework without safe distance. Accidental burning or injured happened from time to time. Why not try a safer solution with remote controller to ignite firework? Firework ignitor system may be very favorable at that time.

Let’s try to demonstrate how to use the firework ignitor system to ignite fireworks.

First, we need the following material.

1× receiver box of firework ignitor system

1×transmitter

2×electric igniters

Second, it is fairly simple connection:

Connect two wires of electric igniter 1 to Out A; Then connect two wires of electric igniter 2 to Out B. Switch on the receiver after connections.

Press button 1, ignite igniter 1.

Press button 1, ignite igniter 2.

Short Video:

http://www.youtube.com/watch?v=S_NgSziVcvc&feature=youtu.be

Online shop: www.carymart.com

Caution:

Any inflammable and explosives material must be far away when igniting fireworks.

Anyone is far away from the firework more than 50m when it is ignited.

Firework Ignitor System for launching 2 Electric Fireworks Remotely

Fireworks burst at curtain of the night just like flowers in blossom, giving us stunning visual sense and bringing high spirit in festivals or big events.

However, some people may be injured during playing fireworks because of improper use. If we play fireworks by a little gadget, the accidental burning can be reduced. Firework remote controller may be a better choice when we ignite fireworks.

We try to demonstrate how to use the firework ignitor system to ignite firework.

First, we need the following material.

1× receiver box of firework ignitor system

1×transmitter

2×electric fireworks

Second, connection is fairly simple:

Connect two wires of electric firework 1 to Out A; Then connect two wires of electric firework 2 to Out B. Switch on the receiver after connections.

Press button 1, ignite firework 1.

Press button 2, ignite firework 2.

Short Video:

http://www.youtube.com/watch?v=-x2z1NYPORE&feature=youtu.be

Online shop: www.carymart.com

Caution:

Any inflammable and explosives material must be far away when igniting fireworks.

Anyone is far away from the firework more than 50m when it is ignited.

2 Channels Toggle Mode Remote Control Kit Operate Swimming Pool Light and Pool Pump

More and more families have swimming pools in their houses or villas. They can swim in the scorching summer with joy. Surely, when the night falls, swimming pool will become more beautiful with lighting. In addition, there is usually swimming pool pump for drawing water into the swimming pool. We always switch them on and off one by one. It is not convenient to do so. To remote control them is a great idea for us. Most of us want to be able to control both independently using one remote control with multiple buttons.

Using this rf 2 channels toggle remote control set is very favorable for this situation.

Pool light and pool pump can be controlled by two different relays independently and they won’t have interference for each other. Toggle mode makes that each button on the transmitter can only control one device.

Here shows the demonstration.

Material preparation:

1×transmitter

1×receiver

1×light

1×AC motor

Power supply

We make sure wire the correct relay to the corresponding device. Paired with relay 1, AC motor connects to the L&N terminals of relay 1 on the receiver. Likewise, the light connects to the L&N terminals of relay 2 on the receiver. The receiver should be powered.