October 2013 – Page 2 – Remote Control Everything

How to Remote Control Dust Catcher

Question from customer:

I want to remote control a motor of dust catcher. It is 1400W, 220V and 6A. I wonder if you have any favorable suggestion for me ?

Answer:

Our suggestion is that you can choose our 1 channel high power ac voltage output long distance remote control kit (S1PX-AC220-ANT2 & CB-2). It is very convenient to you because you don’t have to supply any power for controlled device. Controlled device will get power through receiver when receiver is power on. The maximum current of this kit is 30amp. So it is more than your requirement.

Working distance of remote and receiver set is 2000m (6000ft) in open field if we add external extended antenna in it.

Here is the wiring diagram for your reference.

From the inside structure of dust catcher above, we know that electric motor of dust catcher is connected to OUTPUT L&N terminals. You can set latched working mode. Press big button, motor begins to work. The fan drives rotating brush to absorb dust from intake port to dust bag. You can start to vacuum rooms. Press small button, motor stops working. Vacuum cleaner stops vacuuming. Through this remote control, we can remote control vacuum cleaner on and off.

Handset Wi-Fi Controller for AC Motor

When we want to control electric devices, we always try to make the wiring, connection and operation easy. If you want electric device can get power supply through the remote controller instead of supplying another power, we’d like to introduce the cell phone Wi-Fi controller with DC or AC voltage output to you.

It supports 2.1 ~ 4.0 version Android software system and 4.6 ~ 6.1 version iSO software system. But here we introduce the use under android system. It is applied in modern agriculture field, smart home, instruments, equipment control. Wi-Fi remote control lights, motors, fan, electric doors / windows, aircraft, remote cars, remote toys, rolling blinds, pumps, winches, or other electrical devices with voltage AC110~240V or DC0~28V.

Here is the controlling procedure of AC motor for your information. The material is Wi-Fi controller, mobile phone, AC motor and power adaptor.

Connect the motor to the output terminals of WIFI controller as the wiring diagram shown.

Switch on the power of WIFI controller. Wait until power led, ready led and link led turn on. So the Wi-Fi network is connected. After wireless network connection, press the icon of WIFI Controller software to turn it.

Set up working mode for each channel of relay. Four working modes Toggle, Momentary, Latching and Time Delay are provided.

Set up Momentary control mode: Click the ▼ icon of any channel. Choose M (Momentary) control mode.

Press and hold button 1, the motor is positive rotation. Release button 1, motor stops.

Press and hold button 2, the motor is reverse rotation. Release button 2, motor stops.

Video:

Power Direct Ouput Remote Controller for Air Compressor

Question from customer:

I have an air compressor that sits about 100’ away, and want to open an air valve to actuate the blown horns that I have installed in the center of the arena. Do you have a setup that I can purchase or any suggestion?

Answer：

We recommend the model of DC voltage output remote control kit (S1X-DC12&C-2). It is voltage output receiver so you can connect a 12V battery to this receiver and connect your air valve to the output of this receiver, the air compressor can get power through receiver. Then you can use the remote to control them.

The remote control operates in toggle, momentary and latched mode (set the mode as you like freely). We suggest setting latched mode because the receiver pairs with 2-button transmitter. One button controls “On”, another button controls “Off”.

Wire air compressor to the receiver as the following picture shown. This receiver is designed with voltage direct output configuration. You can wire your air compressor to terminals A&B of the receiver and then supply 12V power to receiver.

Operation:

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.

Control mode Latched: Press -> On, other relays Off; Press another button -> Off.

Press button 1: open the air valve, turn on the air compressor.

Press button 2: close the air valve, turn off the air compressor.

Toggle Remote Controller for 2 LED Lights

Question from customer：

Hello, can you supply me with 2 single on/off receivers with using just 1 transmitter? I have 2 separate 24 volt led lamps in separate locations in my motor home, but I just want to operate all lights from 1 transmitter.

Answer：

We recommend you 2 voltage output toggle receivers (S1XT-DC24) and 1 transmitter (C-2). Wire each led lamp to each channel of receiver. It is voltage direct output. The led lamps can get power through receiver directly. It outputs DC24V power. With fixed toggle working mode, you can use transmitter to press button 1 & 2 to turn on lamps, and then press again to turn off lamps. There is no interference between receivers.

We prepare a simple demonstration for your reference. At first, we prepare the following material.

They are remote control kits, led lamps, power adaptors, lines

According to the following wiring diagram, we made wiring. Two led lamps are connected to A&B terminals of receivers respectively. And supply 24V power to receiver.

Press button 1, switch on lamp 1.

Press button 1 again, switch off lamp 1.

Press button 2, switch on lamp 2.

Press button 2 again, switch off lamp 2.

Video:

30amp Output Cell phone Wi-Fi Controller for AC Lamp

Wi-Fi is a sort of short-area wireless networking, which is available in home or other public places, such as canteens, shopping malls, parks, theatres, cinemas. It can allow computers, Smartphones and other gadgets to access to internet without a wired connection. Our product is combined Smartphone with remote receiver via Wi-Fi networking to make Smartphone Wi-Fi Controller.

This kind of Wi-Fi controller is 30amp high current and ac or dc voltage direct output, that is to say, you don’t need to connect the controlled devices to its own power source. They will get through this receiver. It supports 2.1~4.0 version Android Software system and 4.6~6.1 version iOS software system. Here, we will show you how to use this Wi-Fi controller control AC lamp under Android system.

Let’s go through the procedure. Here is the material.

Wiring is fairly simple. You can wire ac lamp to the Output 1 as the wiring diagram shown. There are 8 Output terminals, so you can wire at least 8 devices.

After finishing wiring, we turn on power. The LEDs of “Power”, “Ready” and “Link” are on one by one. We begin to operate. After wireless network connection, press the icon of WIFI Controller software to turn on it.

There are 4 working modes in it, which includes Toggle, momentary, latched and time delay modes. Toggle mode is used to control lights.

Press button 1, turn on lamp.

Press button 1 again, turn off lamp.

Video: